Showing results: 541 - 555 of 1102 items found.
-
784253-01 -
NI
The CP500X is a coaxial passive probe with fixed 10X attenuation for oscilloscopes that provide 1 MΩ input impedance. It is 1 meter in length. The CP500X attaches to BNC connections on both the signal input and instrument sides.
-
784254-01 -
NI
The CP400X is a coaxial passive probe with fixed 10X attenuation for oscilloscopes that provide 1 MΩ input impedance. It is 2 meters in length. The CP400X attaches to BNC connections on both the signal input and instrument sides.
-
350C Series -
Venable Instruments
Venable Model 350c is the 3 channel successor to the original workhorse Model 350a/b that launched in 1986 and established Venable Instruments as a market leader. The contemporary 350c Series incorporates a 3rd channel, allowing the user to measure more transfer functions simultaneously with one sweep, such as source and load impedance. The 350c is the only frequency response analyzer in the industry that can measure absolute phase, using a reference channel.
-
EC-Series -
Global Energy Innovations, Inc.
The EC1000™ and EC2000™ are the only handheld, Multi-Frequency, ElectroChemical Battery Analyzers on the market using CELScan™ technology. This means they can report both the Electrical (Impedance & Voltage) and Chemical (Sulfation and Dryout) properties of lead acid batteries (VLA, VRLA, GEL). Other battery types (NiCd, NiMH, Lithium-Ion and others) may also be tested using the EC1000™ and EC2000™.
-
Texas Co.
Probes connect the input of the oscilloscope to test points on the device under test (DUT). There are many types, including: high impedance passive, low capacitance, single-ended active, differential active, high voltage, and current probes. This is the first in a series of three articles on probe selection and application, and will focus on passive probes. Part 2 and part 3 will address active probes and current probes, respectively.
-
Ametek Scientific Instruments
Potentiostats control a voltage and measure a resulting current. The Control Amplifier outputs power to the counter electrode (also called auxiliary electrode). A feedback loop is established to control the cell potential between the reference and working electrode. This voltage is measured by the input electrometer, that has a high impedance. This current is then measured between the working and counter electrodes while this potential is maintained at the working electrode and reference electrode.
-
LMV358 -
SparkFun Electronics
This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the feedback path. The bandwidth is set to 15.9kHz by a pair of feedback capacitors, or over 100kHz with the caps removed. The LMV358 opamp can source up to 160mA and works well as a low impedance driver/buffer.
-
AM-360TRN -
Ketai instrument (kunshan) Ltd.
7 Function 20 range DC voltage can be measured 0~1000V AC voltage can be measured 0~1000V DC current can be measured 0~10A buzzer, on-off resistance can be measured 0~20MΩ battery measurement transistor measurement db measurement input impedance 20KΩ/ DVC 9KΩ/ACV Accessories include: battery 1.5Vx1, meter pen, manual, color box
-
Model 2031 / 2031A -
Aplab Limited
- Compact Two in One Instrument with Level Oscillator & Level Meter- Selectable Spot Frequencies upto 4KHz- Digital dB Meter to Measure Level from-60dBm to +20dBm- Under / Over Range Indication- Built-in Rechargeable Battery- Lo-Batt Indication- Easy to Operate, Light in Weight & Portable- Selectable Spot Frequencies from 200Hz to 4000Hz- Extra Switchable Input & Output Impedance of 1120 ohms)
-
M531 -
ETC
The M531 is a single channel USB arbitrary waveform generator compatible with USB 2.0 and USB 1.1 interface. The generator has two outputs: both generate same waveform, but with different peak-peak voltage. The low level output has 50ohm output impedance and maximal peak-peak voltage of 9V. There is no external power supply required to enable low level output (it is powered from USB bus).
-
11667L -
Keysight Technologies
The Keysight 11667L is a 50 ohm two-resistor type power splitter with BNC connectors. It is used with the E5061B network analyzer for power distribution network applications, such as DC-DC converter output impedance measurements with shunt-thru method (100 Hz to 10 MHz). It provides excellent amplitude (<0.2 dB) and phase tracking (+/-3), ensures highly accurate power splitting and low SWR minimizes measurement uncertainty.
-
Keysight Technologies
The Keysight DC blocks offer a new level of DC blocking with performance specified from 50 kHz all the way up to 67 GHz. Precision coaxial connector interfaces ensure an excellent impedance match across wide bandwidths, and come in a variety of RF connectors to fit your application needs. Two choices of DC Voltage ratings make these suitable for a wide range of applications.
-
10073D -
Keysight Technologies
The Keysight 10073D passive probe is our most rugged 500 MHz probe. With a 10:1 attenuation ratio and high 2.2 M ohm input impedance, it is ideal as a general purpose, high bandwidth passive probe for the Keysight 300 MHz - 1 GHz 6000 series, 7000, 8000 and 9000 Series oscilloscopes. The probe identification feature automatically configures the oscilloscope for the probe attenuation.
-
Chroma Systems Solutions, Inc.
Some of the key features to look for in an LCR meter (also known as an impedance meter) are: accuracy, test frequency, measured parameters, test voltage and test current. Additionally, an easy to understand display of test results and the ability to access and use these results has become increasingly important. Component testing often requires much more than simply a resistance, capacitance or inductance value at a given test frequency and stimulus voltage. An LCR meter or impedance meter must have the flexibility to provide multi-parameters over wide frequency and voltage ranges.
-
HCTS Series -
Shanghai Jiuzhi Electric Co., Ltd.
The HCTS Series Cable Heat Cycle Test System is designed to raise and control the temperature of conductor or other low impedance electrical loop to simulate the current loading conditions found in the electrical circuits up to 10000A.