Showing results: 556 - 570 of 1102 items found.
-
Avtech Electrosystems, Ltd.
These instruments generate current pulses whose amplitude is largely independent of the load voltage. This makes them ideal for pulsing device whose voltage may vary with time (for instance, the voltage drop of laser diodes may vary with temperature, or explosive squibs which change impedance during ignition). This voltage independence is a trade-off with speed. If faster rise times are required, consider using pulsed voltage instruments instead.
-
Analog Devices Inc.
Analog Devices JFET input op amps or FastFET high speed (>50 MHz) input op amps provide high input impedance and ultralow input bias currents for high speed applications. The majority of our FET input op amps feature wide supply ranges from +5 V to 12 V or higher and feature rail-to-rail outputs enabling wide dynamic range.
-
ALTO-IRT-7000 -
Alto Inspection Corp.
ALTO-IRT-7000 (IMPEDANCE RESONANCE TECHNOLOGY ) FILM THICKNESS METROLOGY TOOL UTILIZES NON-CONTACT CAPACITIVE AND EDDY CURRENT TECHNOLOGY TO ANALYZE MICRO SECTORS ON COATED SURFACES THAT ARE 1000 TIMES SMALLER THAN ANY COMPARABLE EDDY CURRENT PRODUCTS. BUT MOST IMPORTANTLY, THIS UNIQUE IRT TECHNOLOGY ALLOWS FOR SOPHISTICATED ANALYSES OF THE CONTINUOUS AND DISCRETE FILMS BELOW 50 ANGSTROMS, DRAMATICALLY IMPROVING THE ACCURACY OF QUALITY CONTROL READINGS.
-
EZstat Pro -
NuVant Systems, Inc.
The EZstat Pro potentiostat/galvanostat uses a versatile menu-driven waveform generator (periodic or aperiodic) with preset battery cycling, Tafel plots, and cyclic voltammetry procedures.Users can program sequences of steps blending current and potential control with a resolution of 8 uS/point. EZstat Pro can perform electrochemical impedance spectroscopy (EIS) and uses active IR compensation. The instrument can interface with the EZpump peristaltic pump for flow batteries and fuel cells.
-
FLIR DM66 -
Teledyne FLIR
The DM66 digital multimeter is ideal for automation field service or electronics technicians, providing a comprehensive feature set including low impedance (LoZ) mode, frequency, diode, capacitance, and a Type K thermocouple input for temperature measurement. The multimeter combines rich features, precise measurements, and quality construction into a tool of exceptional value. Easy to use and built to last, the DM66 offers long-term stability for everyday use.
-
iP30z -
Buddipole, Inc.
The iP30z iPortable Antenna SWR Analyzer is designed for field use and is an excellent choice for working with the Buddipole line of antennas. This compact battery powered unit has an easy to read frequency display and measures SWR as well as Z (impedance) in the HF Band. The SWR readings quickly show you the actual VSWR measurement. This is the easiest way to adjust your antenna quickly in the field without any guesswork.
-
PCIe4LXMCX1 -
Dynamic Engineering
Simple and easy to use. Install PCIe4LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position. XMC´s with up to 8 lanes can be used. The PCIe lanes to/from the XMC are routed per PCIe specifications with matched lengths and impedance control.
-
ABex TM-1149Cx -
Konrad Technologies GmbH
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
ECAD System 2005 -
CM Technologies Inc.
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
Extech Instruments Corporation
Circuit and wiring issues can introduce shock hazards (from grounding issues) and can compromise performance of machinery and equipment (from poor ground impedance, lack of sufficient voltage under load and/or high ground-to-neutral voltage).
-
Schwarzbeck Mess Elektronik
Tuned half-wave dipoles have been among the most important antennas from thebeginning of rf-technique. The characteristics of half-wave dipoles havebeen calculable very early using the Maxwell and Hertz equations. Therefore the halfwave dipole became a reference antenna. The ideal (lossless) half-wave dipole has anisotropic gain of 2.15 dBi and an impedance of 73 Ohm. The directional pattern is circular inthe H-plane, "8-shaped" in the E-plane with the maxima perpendicular on the dipole axis.The half-power beamwidth (-3 dB) is approx. 78°. The impedance of real dipoles isdepending on the thickness/length ratio of its elements, typical values are 60-70 Ohm.Dipoles for industrial applications are available in the frequency range from 30MHz to up to approx. 4 GHz. The dipole elements are length variable (telescopic) orwith fixed length, the latter especially above 1 GHz. The most important applications aretest site evaluations (NSA, normalized site attenuation) and the determination of ERP(Effective Radiated Power) respectively EIRP (Effective Isotropic Radiated Power).
-
HGT1 -
OMICRON electronics
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
Analog Devices Inc.
The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus. Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications.
-
Analog Devices Inc.
Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications. The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus.
-
McLennan Sound Monitoring, Inc
The remote noise sensor assembly consists of a noise sensor mounted in a laser-cut, powder painted, 16-gauge metal chassis. The noise sensor assembly is connected to the main instrument with a four conductor cables and has an “on” indicator LED. Due to the power-balanced low impedance return signal, the remote noise sensor can be placed up to 1000 feet away from the McLennan sound level monitor main instrument without significant change in the signal.