Showing results: 526 - 540 of 789 items found.
-
Series MAT -
Kepco, Inc.
Kepco MAT are linear power supplies that are oriented to systems applications. Their principal control means is a 2-wire, long range, serial bus, Kepco's single address, multiple instrument bus. As many as 27 power supplies, including models in the Kepco MST, MBT and BOP series may be "daisy-chained" on this bus and interfaced either to IEEE 488.2, a PC bus, or to a VXI host.
-
CPCI-48IN -
ALPHI Technology Corporation
The input board consists of three Zilog Z8536 controllers for DC input control. An FPGA provides the timing and control. Each input has its own optical isolation, and supports a hardware adjustable resistor/opto-diode combination for various input voltage ranges. An AMCC PCI controller provides the interface to the host computer. All I/O is accessible from the front panel.
-
NI
PXI Waveform Generators can produce precise waveforms including sine, square, triangle, and ramp as well as arbitrary, user-defined waveforms using sequences of data or streaming continuously from a host or peer-to-peer instrument within the PXI system. These instruments are ideal for tightly synchronized, mixed-signal test systems in scientific research or test of semiconductor devices, consumer electronics, automotive, and aerospace/defense.
-
4900 Series -
Probe Master Inc.
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
-
MMA8452Q (Qwiic) -
SparkFun Electronics
This breakout board makes it easy to use the tiny MMA8452Q accelerometer communicate over I2C in your project. The MMA8452Q is a smart low-power, three-axis, capacitive MEMS accelerometer with 12 bits of resolution. This accelerometer is packed with embedded functions with flexible user programmable options, configurable to two interrupt pins. Embedded interrupt functions allow for overall power savings relieving the host processor from continuously polling data. This version of the SparkFun Triple Axis Accelerometer Breakout includes pre-soldered Qwiic connectors for rapid prototyping and better ease of use. With the connectors already soldered on, you can jump right into using this little board without any assembly!
-
NI
CAN Interface Devices communicate using onboard transceivers for High-Speed/Flexible Data-Rate, Low-Speed/Fault-Tolerant, and/or Single-Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from Fieldbus Exchange Format (FIBEX) and Database Container (DBC) files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
PCI102 -
Vadatech Inc
The PCI102 allows testing of AMC.1, AMC.2 and AMC.3 modules in a PC environment during development and manufacturing; reducing the costs associated with maintaining different platforms. The PCI101 is a PCI-X edge style carrier with PCIe x4 lanes going to the AMC module. The AMC.1 module connects to the host PC’s PCI-X bus via a PCI-X to PCI ebridge. The AMC.2 module’s GbE ports are routed to RJ-45s. The AMC.3 differential pairs are routed to two SATA connectors. ThePCI102 is available with an optional VT001 IPMI controller which can test the AMC IPMI management functionality. The dual I2C bus connectors allow for connecting any I2C bus to any other I2C bus as well as being able to debug and monitor the I2C bus traffic. Provides two current sense resistors to measure the payload power as well as the management power of the AMC. The PCI102 can be powered on the bench without the host PC.
-
Curtiss-Wright Defense Solutions
We simplify tactical data link (TDL) communication with standards-based solutions that are designed to improve tactical communications. Our solutions reduce the time, risk, and expense of TDL implementation and integration, alleviate interoperability issues, and lower lifecycle maintenance costs for militaries and prime contractors worldwide. With support for multiple communication protocols, hosts, and interfaces, our approach to TDL design facilitates interoperability among platforms.
-
PCI-SMN -
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
PEX431 -
Abaco Systems Inc
Designed to enable the development of complex, scalable, high performance 3U VPX systems in today’s increasingly-connected military/aerospace world, the PEX431 is characterized by significant flexibility. The PEX431 Multi-Fabric Switch and XMC Carrier Card allow designers to build complex VPX systems with multiple single board computers and multiple I/O modules. PEX431 supports PCIe switching, GigE switching and the ability to host a XMC mezzanine.
-
TCR180PEX-EL -
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX-EL receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements).
-
RG1 -
North Atlantic Industries
The RG1 Time Code receiver synchronizes to IRIG-A/B/G time codes and provides precise time in a memory register, for the host SBC.The IRIG output of the card can be used to synchronize other IRIG time code readers. Additionally, the RG1 includes a real-time clock (RTC) that may be used as a reference source for IRIG master applications, to free the system processor from the task of updating the master timer.
-
Conversa -
e-con Systems Inc.
Conversa, camera for conversation (See3CAM_CU38), is a 3.4 MP low light USB 3.1 Gen1 camera with built-in stereo microphone providing 16bit audio @48KHz. This low-light USB camera is the next advanced version of our flagship product See3CAM_CU30, with built-in stereo microphone for crystal clear sound. It is a plug-and-play (UVC and UAC) compliant USB 3.1 Gen1 SuperSpeed camera and is also backward compatible with USB 2.0 host ports. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It has a dedicated, high-performance Image Signal Processor chip (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control).
-
Pickering Interfaces Ltd.
Pickering's PXI Microwave Switch Modules vary from simple multiplexer and switch configurations to integrated matrices and large multiplexers. Most products are characterized for 50 operation however certain 75 versions are supplied either as standard or custom products. Remote versions occupy a single PXI slot with the microwave switches mounted separately from the host chassis, connection to the module is via a supplied control cable.
-
FAB111 -
Axiomtek Co., Ltd.
The FAB111 has a PICMG 1.3 CPU card slot for the SHB (system host board) and offers one PCIe x16 slot, one PCIe x4 slots and four 32bit/33MHz PCI slots. Two high-speed USB 2.0 ports, a 24-pin ATX power connector and an 8-pin connector for thermal detected board are featured. The FAB110 is designed for the 8-slot industrial chassis, such as Axiomtek�s AX60551and AX60552.