Showing results: 361 - 375 of 628 items found.
-
WECO 9100 -
Radian Research, Inc.
Radian Research introduces an innovative Time Run solution to our line of multi-position test boards. The WECO 9100 Time Run Board features the highest quality socket design that you have come to expect from the leader in meter testing solutions. The standard WECO 9100 configuration consists of 68 zero insertion force sockets mounted on two back to back panels. A dead front socket design ensures safety by removing energy from sockets that are empty.
-
GX5290 -
Terotest Systems Ltd.
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
PI-2005 -
Pulse Instruments
As a test engineer or digital designer you must have state-of-the-art tools to test, characterize and verify your complex semiconductor devices and digital circuit boards. The PI-2005 Pattern Generator will generate a wide range of simple or complex digital patterns for any test application that requires a serial or parallel digital data stream. To meet the requirements of complex devices and digital circuits, the pattern generator can be configured from 16 to 64 output channels.
-
Test Coach Corporation
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Circuit Check, Inc.
Circuit Check supports reading linear bar codes and 2D symbols within each of its fixture product lines.When spring-loaded probes are not practical or access is limited, Circuit Check can help you with thru-connector tests to contact connectors on any surface or edge of a circuit board. These tests can be implemented spring probes, mating connectors, sacrificial SMT connectors, and stabber cards.
-
17-56 -
Testing Machines, Inc.
The Crush Test is designed as a robust, easy to-use instrument. Exactly what you need when performing crush tests. The Crush Tester is suitable for a wide variety of samples, including corrugated board, tubes, paper and plastics. The special sample holders extend the instrument’s possibilities. The accuracy is achieved with a precision load cell, which is even accurate at low force values.
-
ACS-FC-3U-2 -
AIM GmbH
The ACS-FC-3U-2 is AIM’s high performance CPCIe (PXIe) module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The ACS-FC-3U-2 is a powerful State-of-the-Art 4-lane CPCIe 2.0 compliant CPCIe board.
-
W-IE-NE-R, Plein & Baus GmbH
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
DRK104A -
Shandong Drick Instruments Co., Ltd.
DRK104A cardboard puncture tester is used to test the corrugated board anti-pierced performance (puncture strength). It has the snap-operating handle, automatic reset and safety protection function. It is the indispensable instrument for carton manufacturing plants, research and quality supervision, inspection and other enterprises and departments.
-
UWE Electronics
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Prober Adjustable Family -
Test Electronics
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
Prober Press Rods Family -
Test Electronics
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
SparkFun Electronics
With GNSS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GNSS Real Time Kinematics (RTK) has mastered dialing in the accuracy of their GNSS modules to just millimeters, and that's why we had to put it on this board! With the flexibility of the MicroMod's M.2 connector, you can easily test and swap out different MicroMod processor boards for your application. Simply match up the key on your board's beveled edge connector to the key on the M.2 connector and secure the boards with a screw. This means solderless access to the ZED-F9P modules features via UART1, UART2, SPI, and I2C ports!
-
ViTec Co. Ltd
The system is designed to collect data during model tests in a pilot pool.The complex is built on the basis of a laptop in a protected design, a National Instrumrnts data collection board and two external connector blocks with BNC connectors, allowing you to connect up to 32 analog signals.
-
Peritec Corp.
RFID test system of Peritec is making FPGA board (IF-RIO) the processing of the IF band. This reading of the code, called (Electronic Product Code) EPC is required for RFID tag ISO18000-6 TYPEC of (EPC C1 G2). However, it did not provide treatment too late in the traditional instruments.
