Showing results: 6361 - 6375 of 6936 items found.
-
781440-01 -
NI
16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6351 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6351 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
LMS Series -
Vaunix Technology Corporation
The Lab Brick LMS series of high frequency RF and microwave USB-compatible, synthesized signal generators cover a frequency range from 0.5 MHz - 20 GHz with low noise, fast 100-microsecond switching time, and fine 100 Hz frequency resolution. They require no additional DC supply voltage and offer advanced features such as phase-continuous linear-frequency sweeping, internal/external 10 MHz reference, and optional pulse modulation. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
SMX-7XXX (Microwave) -
AMETEK VTI Instruments
The AMETEK VTI Instruments SMX-7000 Series of microwave switch cards extends functionality typically reserved for dedicated stand-alone systems into the PXIe from-factor. Single and dual slot configurations provide the ability to mix and match multiple switch configurations including SPDT, SP4T, SP6T and Transfer. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers. Ideally suited for medium-to-high density automated test equipment (ATE), the SMX-7000 Series deliver uncompromised measurement integrity ideal for the most demanding aerospace, defense and communication applications.
-
326 -
STAR-Dundee
The SpaceWire Brick Mk3 is a USB 3.0 (also works with USB 2.0 and USB 1.1) to SpaceWire interface device that is suitable for use in all stages of SpaceWire equipment development: initial SpaceWire evaluation, instrument simulation, control system simulation, unit testing, integration support, and EGSE. The SpaceWire Brick Mk3 provides two SpaceWire interfaces, support for high speed data transfer, the capability to inject various types of errors on demand, the ability to transmit and receive time-codes and act as a time-code master, and comes complete with highly optimised host software for low latency transmission of SpaceWire packets directly to and from the host PC.
-
Scientech Technologies Pvt. Ltd.
Data Acquisition Systems have its contribution in a wide range of activities of day-to-day life. Most commonly, it is used to measure the electrical signals from some sensor. These signals may represent the state of a physical process, such as the position and orientation of machine tools, the temperature of a furnace or the size and shape of a manufactured component. Data Acquisition Systems are widely used today in home automation systems, industrial monitoring and control as well as in a variety of other time-critical applications. Installation of Data Acquisition Solutions in Industries is a flexible and cost-effective measurement solutions. Today, Data Acquisition Systems along with "Internet of Things" have led to development of many applications.
-
ZLD-10 -
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.2-2008Used to measure conductor with nominal diameter ≥0.01～9.0mm or various round or flat copper and aluminum wires and other metal wires with DC current resistance of 100μΩ～99.99Ω;Combination of intelligent DC conductor resistance measuring meter and DC resistance test fixture with sample straightening function;Test range can be selected according to the resistance value of sample, and after clamping samples current resistance value would be displayed;Both potential fixture and current fixture are made of copper;The application of microcomputer control allows for full-automatic completion of test;LED will intuitively display measurement results;
-
787137-01 -
NI
PXIe, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), DC Power Supply, Up to 12 GB/s PXI Chassis - The PXIe‑1086DC incorporates hot-swappable, redundant DC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system. The PXIe‑1086DC monitors power supply health/voltages, air intake temperature, and fan health/speed; it provides any failure feedback with the status LEDs located on the chassis. This chassis is ideal for test, measurement, and control applications with demanding system uptime requirements.
-
781156-01 -
NI
8‑Slot, USB CompactDAQ Chassis - The cDAQ‑9178 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data … transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9178 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
Sample Technology
Aiming at the problem of PI, Shengbo Technology carefully studied the root cause of the problem. Through the loop analysis and noise analysis of power supply and automatic control, it provided targeted solutions for frequency response analyzer and power supply rejection ratio (PSRR) analysis . In addition, we also have a professional technical application support team in the field of power electronics testing. We can customize and develop the corresponding system software for customers so that it can be applied to PC / Servo / Telecom power supplies, adapters and chargers, and backlights. Inverter, LED drivers, ballasts for energy-saving lamps (Ballast), and even UPS, PV Inverter, electric vehicle chargers, AC and DC motors, etc.
-
Neutronics Manufacturing Co.
Introduction: Measuring the line loop contact resistance by bridges is not the ideal method as the test current is only a few milli amperes. Thus the value is not the true value of the contact resistance. Model HL- 100 is a direct reading tester, and uses a test current of 100A DC, resulting in true v alue and accur ate measurements. Model HL- 100 adopts digital circuit technique and is used for measuring contact resistance of switch control equipments at test current of 100A DC. The measurements are accurate as the test is highly stable.HL- 100 is a new, fully automatic micro controlled tester that measures contact resistance at 100A DC with built in printer. The advantages of HL-100
-
4405200 -
BI Communications
The TX Ranger is a hand-held Time Domain Reflectometer (cable fault locator) with a first range of 2.5 meters combined with a 1.3 Nano second pulse width gives a blind zone of only 5 cm, it makes this the ideal product for fault location on short cable assemblies and harnesses. Small and intermittent faults can be easily identified by using the selectable gain control allowing trace amplification of up to 7 times and when set to scan lock mode the advanced noise reduction software may be selected allowing the user to select between 8,16 and 32-point trace averaging further enhancing the clarity of the trace by reducing electrical and environmental interference.
-
Part No. LD24KK -
Teledyne Defense Electronics Relays & Coax Switch
The Series LD24KK solid-state relays are screened utilizing MIL-PRF-28750 test methods and are packaged in low profile hermetically sealed cases. These relays are constructed with state-of-the-art solid state techniques and feature fully floating power FET output technology. This allows the load to be connected to either output terminal and provides a low ON resistance. The input and output are optically isolated to protect input logic circuits from output transients. A trip status indicator turns on when an overcurrent condition has occurred and the short-circuit protection has been activated.MSL 1Available options include:LD24KK 5A, 270Vdc Load; 4.2-16Vdc Control, Short Circuit Protection and Trip Status
-
TYPE HFX-1 -
National RF, Inc
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
VAW -
Chuan Sheng Electronics Co., Ltd.
VAW DC Multifunction Power Meter provide high accuracy measurement, display and communication of DC voltage, Current, Power, Energy(import / export), and Run Hour. They are also building in 4 Relay outputs, 1 Analogue output, 1 Pulse output , 2External Control Inputs and 1 RS485(Modbus RTU Mode) interface with versatile functions such as remote I/O, alarm and communication for DC power applications like as solar, wind power system or portable electronic device consumption testing.For the power saving, VAW has built in an innovation timer to switch down the light and power of LED. It makes sense to build the meter in a green power system.
-
ETF-SERIES -
Envisys Technologies
Precise Temperature Accuracies with Reliable Test Results Temperature Limits: -40/-60 °C to 30 °C Temperature Accuracies: ±2-3°C Temperature Rate of Change: 20-25 deg /min (Non-linear) Maintenance Free Access to The System Self-Sufficient System Compact with small footprints suitable for any space constraint laboratories Low decibel system Suitable for testing electronic chips / devices Environmentally friendly refrigerants Efficient heating Microprocessor based single set point PID temperature controller with data logging Flexible hose up to 2.5-3.0m Interchangeable heads according to chip size. Inbuilt electrical control panel with switchgear system
