Showing results: 106 - 120 of 325 items found.
-
partector 2 -
Naneos Particle Solutions gmbh
The naneos partector 2 is the world's smallest multimetric nanoparticle detector. The partector 2 uses dual non-contact detection stages to measure not only lung-deposited surface area like the partector 2 Light, but also particle number concentration and average particle diameter. Additionally, ultrafine particle (UFP) surface and ultrafine particle mass concentrations are calculated and displayed. In contrast to some of our competitors, the UFP mass is displayed online, and it is calculated using the measured diameter of the particles, rather than estimated by a simple multiplier for LDSA.
-
ZETA-check -
Particle Metrix GmbH
Particle interface potentials like the oscillating zeta streaming potential measured in the ZETA-check, represent the level of electrostatic repulsion between particles. The potential is generated by ionic end groups on particles and macro-molecules, respectively. With ZETA-check, the state of the actual charge of dispersions and macromolecular solutions is obtained within seconds. Solutions and dispersions from 0.3 nm up to 100 µm particle size qualify for measurement.
-
MSP Corporation
TSI’s environmental monitors measure size fractions of particles and ultrafine particles. They capture PM1, PM2.5, Respirable PM4, PM10, and Total PM.
-
Rocky Mountain Laboratories, Inc.
Raman is used to analyze organic and inorganic materials. Bulk and small particle materials can be analyzed. Raman microscopy allows for the identification of particle as small as 1 µm.
-
-
Aero Nav Laboratories, Inc.
This test method is divided into two procedures. The small particle procedure, using fine dust is performed to ascertain the ability of equipment to resist the effects of fine particles which may penetrate into cracks, crevices, bearings, and joints. The blowing sand test, using coarse particles, is performed to determine whether equipment can be stored and operated under blowing sand conditions without experiencing degradation of its performance, effectiveness, reliability, and maintainability due to the abrasion or clogging effect of large, sharp-edged particles.
-
-
-
2070 -
Elcometer Limited
The Elcometer 2070 NPIRI Fineness of Grind Gauge is used to determine particle size and the fineness of grind of particles in printing inks according to the National Printing Inks Research Institute (NPIRI) scale.
-
OBS-ONE PN Unit -
HORIBA, Ltd.
The OBS-ONE PN unit is an on-board emissions measurement system for analyzing the solid particle number concentration within the specified particle size range under real-world driving conditions. The unit uses a condensation particle counter which is recommended principle by the Particle Measurement Programme (PMP), one of working groups affiliated with UNECE.The PN unit combines with the GAS unit to measure the specified exhaust gas components, along with the exhaust gas flow rate, the GPS position, and the atmospheric conditions (temperature, humidity, pressure).
-
-
ZetaView® -
Particle Metrix GmbH
ZetaView® Nanoparticle Tracking Analyzer for hydrodynamic Particle Size, Zeta Potential and Concentration. With ZetaView® individual particle tracking, classical micro-electrophoresis and Brownian motion are presented as modern analysis tools. Auto-alignment and auto-focusing make the “Seeing is Believing” principle user friendly. By sub-volume scanning robust results of zeta potential and size histograms are derived from thousands of particles.
-
Dantec Dynamics A/S
The Shadow Sizer measures size, shape and velocity of particles using backlighting and image analysis software based on the shadowgraphy technique.The Shadow Sizer can measure a wide range of particles types including bubbles, liquid droplets, solid particles and any object with a well-defined contour.Data is analyzed by DynamicStudio and includes histograms of size distribution, 2.5D spatial distribution plots, cumulative histograms and tables.
-
Eurofins E&E
Ingress Protection testing evaluates the resistance to particle and liquid entry for an enclosed product. After testing has been performed, the product receives an IP rating, based on IEC 60529, according to the achieved resistance to solid particles and liquids.
-
Rocky Mountain Laboratories, Inc.
FTIR Analysis is used to analyze organic materials. Bulk and small particle materials can be analyzed. FTIR microscopy allows for the identification of particle as small as 10 µm. Determination of unknown materials is facilitated by spectral matching to a library of over 250,000 reference spectra.