Showing results: 466 - 480 of 538 items found.
-
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata 980 HDMI Phy & Protocol Aux Channel Analyzer module supports compliance testing of the HDMI DDC bus and HDMI 2.0 CEC testing (partial support only). The module’s CEC compliance tests enable you to identify compliance failures early in the development cycle. The solution is ideal for pre-testing and self-testing (where permitted) your HDMI 2.0 device. The module also supports compliance testing of the HDMI DDC bus voltage and timing parameters in accordance with HDMI 1.4b. Future releases of the module will support functional tests and compliance tests on other HDMI auxiliary channels.
-
CA-RD(H) -
Cincinnati Sub-Zero Products
CSZ's rapid decompression test chamber is designed to simulate rapid decompression for testing aircraft avionics. The environmental chamber meets the environmental conditions and test procedures for airborne equipment referenced in the RTCA DO-160 test specification. The DO-160 specification was designed to test sudden pressure changes starting from 8,000 feet to 60,000 feet (536 to 55 Torr) in 15 seconds. An altitude of 8,000 feet (536 Torr) was used for the initial cabin altitude and 60,000 feet was used for the final cabin altitude after decompression. This test specification is used to identify failures of materials inside of the cabin and the reaction to the surrounding environment.
-
PP-TOFMS -
HORIBA, Ltd.
Plasma Profiling TOFMS addresses the needs of materials scientists across a wide range of application areas. PP-TOFMS provides fast elemental depth distribution of any inorganic material. The speed and ease of use of PP-TOFMS permit to reduce optimization time of growth processes as many research scientists strive to reduce the time from discovery to applications of new materials.The simultaneous full coverage of TOFMS available for each point of depth permits the detection of non suspected contamination. This is key for failure analysis and optimization of thin film processes that tend to no longer be based on ultra-high grade methods (i.e. ink jet printing…).
-
IVA® MODEL 210S -
Oneida Research Services, Inc
The IVA® system is specifically designed for the quantitative analysis of low molecular weight gases contained in hermetic packages, cavities and other enclosures. The Model 210s concept integrates automated hardware with easy-to-use icon-driven software. Its design permits routine quality control, failure analysis and research level testing operation as a turn-key analytical system. The IVA® Model 210s includes a high-performance, quadrupole-mass spectrometer analyzer, a sample-mounting interface and precision hardware. The instrument is also computer-controlled and equipped with exclusive ORS integrated system control software — which provides instrument control, data analysis, data archiving and ease of operation.
-
IPMT-3 -
FM SYSTEMS, INC.
The IPMT-3 is a precision attenuator used to test IP video systems to insure that you have an adequate digital signal margin. Digital signal margin is the amount of signal level above the digital cliff that you have in your system to prevent a picture failure from occurring. IP cameras will give you a perfect picture until the network cable loss reaches beyond the minimum allowable signal level and then you suddenly get no picture at all. This effect is called the digital cliff, because like walking off of a cliff, everything is great till you take the last step off the edge and then all is lost.
-
WECO 9000 -
Radian Research, Inc.
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
National Technical Systems
Surface Insulation Resistance (SIR), as defined by IPC, is the electrical resistance of an insulating material between a pair of contacts, conductors, or grounding devices that is determined under specified environmental and electrical conditions.In respect to the world of printed circuit boards (PCBs) and printed circuit assemblies (PCAs), SIR testing—also commonly referred to as Temperature Humidity Bias (THB) testing—is used to evaluate a product’s or a process’ ability to resist “failure” by means of current leakage or an electrical short (i.e., dendritic growth). SIR testing is typically performed under elevated temperature and humidity conditions—such as 85°C/85% RH and 40°C/90%—with periodic insulation resistance (IR) measurements obtained.
-
4012 -
Barth Electronics, Inc
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
WABC -
Wuhan Sangao Electrical Test Installations Limit Co.
Acc to IEC and Relevant national standard, In the power transformer production, transfer and user test process, Transformer ratio test is necessary project, This can be used for quality supervision of transformer factory and the use process, prevent the transformer winding inter turn short circuit, open circuit, connection error, pressure regulating switch failure or contact fault.So our company development and production of automatic ratio tester in the original basis according to the user's site using requirements , make the operation more convenient, complete function, stable and reliable data, the testing speed is greatly improved.To meet the needs of all kinds of small medium and large transformer ratio test.
-
Model 4702 -
Barth Electronics, Inc
The Model 4702 HMM+™ is a completely new tester primarily intended for device level testing and produces a current waveform as specified in the IEC-61000-4-2, from a 50 ohm source impedance system.*This tester provides device level test data that allows users to evaluate the IEC current waveform protection level of their devices. We included failure identification by leakage current increases in the 4702 tester so precise pass/failure levels can be closely measured.*The 4702 HMM+™ provides a new and improved test connection method for making quantifiable and repeatable device level HMM measurements.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
MS561 -
MSG Equipment
Multifunctional equipment for testing EPS units. The device simulates real operation of a unit in a car, invented to diagnose pumps with electric power steering, it can be used jointly with hydraulic bench to test mechanical pumps, or separately from the bench to test electric part of a unit. The Controller tests EPS racks and columns directly in a car (if there is access to sockets) without dismounting of a unit. This method eliminates problems with wiring and other electronic units. The device has also OBD II connector for diagnostic scanner to detect errors. Besides diagnostics, the Controller contributes to more effective repair of a unit. The equipment can be placed on a table due to its small dimensions. Separate part of EPS unit can be connected to the device to analyze failures.
-
MMPD -
McGan Technology
McGan Technology’s MMPD-8K electrosurgical insulation defect detector is a battery operated unit that tests the integrity, such as pinholes, cracks or defects, of the insulation of electrosurgical instrument in order to prevent inadvertent tissue burns which may occur during electrosurgical instrument procedures. The integrity of the insulation of electrosurgical instruments can occur over time, through normal surgical use, through the accidental contact with a sharp instrument or the rubbing of the insulation to the point of abrading it. The insulation failure provides an alternate pathway for the current to leave the instrument’s electrode usually beyond the sight of the surgeon which will result in the unintended tissue burn. Using an electrosurgical test equipment maintenance program can greatly reduce the number of these inadvertent burns during electrosurgical procedures.
-
412B -
Oersted Technology
The Model 412B magnetizer provides many of the features of the Oersted Technology 300-series magnetizers in a small benchtop cabinet. This unit is designed for magnetizing parts which require lower energy levels due to their size or the magnetic material used. Like the 300-series magnetizers, the 412B is an ECS magnetizer, which allows the user to electronically vary the capacitance of the unit. The capacitor banks are internally discharged through a safety circuit in case of power failure or accidental power-down. When the 412B is connected to a properly equipped fixture, the front-panels can be inhibited through an overtemperature interlock circuit, preventing the magnetizer from being operated once the fixture begins to overheat. An external output is also provided for monitoring the magnetizing current pulse with an oscilliscope.
-
MS111 -
MSG Equipment
The test bench is intended to test AC compressors of wide range of vehicles on R134a refrigerant. The equipment detects failures of a vehicle unit before its mounting in a car, whether it is a remanufactured, repaired unit or a used one. In the process of testing, data is shown on LCD display. It gives an opportunity to follow testing results realtime, save and/or print them due to software special features. Unit fixation mechanism is very flexible: a compressor can be easily fixed, no matter what kind of fittings it has. Units with electromagnetic clutch or electromagnetic valve can be tested both separately and simultaneously. Peculiar features of electric commutation are considered, connection polarity is identified automatically, indicator on the control panel indicates on presence of a diode in a circuit.
-
Intego GmbH
Due to their special material properties, ceramic and glass components are the basis of many high-tech products. The same properties make the production complex and costly. Substrate defects that lead to failure of finished components should be avoided at all costs. For this reason, early automated optical inspection is essential.For the inspection of sapphire and quartz glass Intego has developed systems to detect both external and internal defects and can also provide cutting suggestions. Using index matching it is possible to test rough or uneven glass profiles.For the inspection of ceramic components Intego offers solutions specifically tailored to the respective testing task. Our modular design uses standard components that have already been developed and tested and in most cases only requires minimal adaptation.
