Showing results: 3106 - 3120 of 5003 items found.
-
TE6100 -
TEAM SOLUTIONS, INC.
The TE6100 is the first 100 MS/SEC measuring instrument that consists of a Digital Storage Oscilloscope, Spectrum Analyzer, Transient recorder and Voltmeter. This new PXI based, compact measuring instrument, can solve almost every measurement problem. Analyzing signals is done with an 8-bit resolution and a maximum sampling speed of 100 MHz. The input ranges 0.1 Volt full scale to 80 Volt full scale. The record length is 32K/64K samples.
-
11930B -
Keysight Technologies
The Keysight 11930B limiter provides input protection for a variety of RF and microwave instrumentation. Failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage. The Keysight 11930B provides the same protection to spectrum analyzers and sources. At even greater power levels, failure mode for limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
AD-902 -
ADEX Urzadzenia Pomiarowe
The instrument is designed for the direct measurement of insulation resistance of cables and electrical equipment especially in the telecommunications and communications. It can also serve as a tester for example go. Circuits or connectors.
-
8003 -
Spanawave Corporation
The Spanawave Model 8003 Precision Scalar Network Analyzer combines a 90 dB wide dynamic range with the accuracy and linearity of a power meter in a signal instrument.
-
KATflow 10 -
Katronic
The KATflow 10 is a simple ultrasonic clamp-on flow monitor, which provides an extremely cost-effective alternative to in-line flowmeters on effluent, wastewater and sludge applications. The KATflow 10 is used to monitor the flow of liquids containing higher levels of solids or entrained gas bubbles for measurements where a general flow indication is sufficient. The instrument is extremely simple to install and commission and is ideal for applications which demand good repeatability and reliable results.
-
WIKA Alexander Wiegand SE & Co. KG
Wherever the process pressure has to be indicated locally and, at the same time, limit values must be monitored, contact pressure gauges find their application. The switch contacts make or break circuits dependent upon the pointer position of the indicating measuring instrument. If the reading is significantly above or below a set value, they trigger an alarm, hence also the term “alarm contact”. Contact pressure gauges are also suitable for starting, stopping or switching processes.
-
Chandler Engineering
Data Acquisition And Control Software offers complete control over the temperature and pressure schedules of oilfield laboratory instruments from a personal computer. Digital Chart Recorders provide secure data storage and digital backup of critical test data. Previously sold as ancillary equipment on all Chandler Engineering HPHT cement consistometers, pen and paper chart recorder technology is rapidly becoming obsolete as industry demands change.
-
Qingdao Hantek Electronic Co., Ltd.
multi-function like arbitrary waveform generator, pulse generator, 16-bit word generator, 7-digit cymometer and function generator; It can generate and output stable, accurate and low distortion signals; Built-in over 150 type arbitrary waveforms, which is easy to simulate various signals; Its large screen, user-friendly interface design and keyboard layout are convenient to use; Rich standard configuration interfaces easily achieve remote control of the instrument.
-
HPR-40 DSA -
Hiden Analytical Ltd.
Hiden Analytical offers class-leading gas monitoring solutions designed to obtain and quantify complex species in liquid samples. Our ultra-precision HPR-40 DSA is a compact membrane inlet mass spectrometer (MIMS) and a versatile instrument suited to dissolved and evolved species analysis. Direct probes, flow through probes and large circular membrane cells are available to address a broad application range in sediment, sea water, sludge and groundwater studies.
-
SKS-H04GA -
Shanghai Sanki Electronic Industries Co., Ltd.
The high-frequency noise simulation generator is an EMC test instrument that reproduces high-frequency noise with a fast rise time when the switch is turned on/off. Since the pulse rise time is less than 1ns and contains wide bandwidth noise, it is very suitable for reproducing malfunctions. The line noise entering the power line and the induced noise entering the communication line can be reproduced, and the performance evaluation of the malfunction and function degradation of electronic products can be performed.
-
IMI-PSI -
Hiden Isochema Ltd
The IMI-PSI is designed to investigate gas sorption by nanoporous materials, from sub-ambient pressures to 200 bar. Its inherent flexibility allows both BET surface area analysis and gas storage studies to be performed using only one instrument, while an optimized design and superior build quality ensures high accuracy. Full automation enables pre-programmed gas switching and sample pretreatment routines to be set for ease-of-use.
-
Avtech Electrosystems, Ltd.
Are high-voltage pulse generatorscapable of driving 50 (or higher) loads and operating over a wide pulse width range. The instruments include IEEE- 488.2 GPIB and RS-232 interfaces. For diode loads, thesemodels can be used to provide up to 1, 2, 4, 5 or 8 Amps of pulsed current if the diode is connected in series with 50. All models operate over a wide pulse width range of 100 nsto 100 us.
-
PGY-I2C/SPI-EX-PD -
Prodigy Technovations Pvt. Ltd.
I2C Protocol Analyzer and SPI Protocol Analyzer (PGY-I2C/SPI-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-I2C/SPI-EX-PD is the leading instrument that enables the design and test engineers to test the respective I2C or SPI designs for its specifications by configuring the PGY-I2C/SPI-EX-PD as Master/Slave, generating I2C/SPI traffic and decoding the I2C/SPI protocol decode packets
-
Bruker microCT
Micro computed tomography is X-ray imaging in 3D, by the same method used in hospital CT scans, but on a small scale with massively increased resolution. It really represents 3D microscopy, where very fine scale internal structure of objects is imaged non-destructively. Bruker microtomography is available in a range of easy-to-use desktop instruments, which generate 3D images of your sample’s morphology and internal microstructure with resolution down to the micron level.
-
Measure Tech, Inc.
Micro computed tomography is X-ray imaging in 3D, by the same method used in hospital CT scans, but on a small scale with massively increased resolution. It really represents 3D microscopy, where very fine scale internal structure of objects is imaged non-destructively. Bruker microtomography is available in a range of easy-to-use desktop instruments, which generate 3D images of your sample’s morphology and internal microstructure with resolution down to the sub-micron level.