Showing results: 1996 - 2010 of 5237 items found.
-
40-972B-200-1m-FU -
Pickering Interfaces Ltd.
This female rear exit to unterminated 1m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to its mating connector by female screwlocks.
-
40-971B-200-0.5m-FF -
Pickering Interfaces Ltd.
This female rear exit to female ribbon 0.5m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks.
-
40-971B-200-2m-FF -
Pickering Interfaces Ltd.
This female rear exit to female ribbon 2m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks
-
40-971B-200-1m-FM -
Pickering Interfaces Ltd.
This female rear exit to male ribbon 1m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks.
-
40-971B-200-0.5m-FM -
Pickering Interfaces Ltd.
This female rear exit to male ribbon 0.5m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks.
-
40-971B-200-1m-FF -
Pickering Interfaces Ltd.
This female rear exit to female ribbon 1m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks.
-
40-971B-200-2m-FM -
Pickering Interfaces Ltd.
This female rear exit to male ribbon 2m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks.
-
910102107 -
Virginia Panel Corporation
Consists of 2 tools for installing cabling into the contact. Crimp Tool and Locator for center contact and Hex Crimp Tool for outer shield (p/n# 910104139).
-
CB52 -
CAMI Research Inc. (CableEye®)
The CB52 is intended for periodic calibration verification of the Kelvin 4-wire resistance measurement module – an optional, add-on module that may be purchased with any new hipot system, or added to an existing high voltage tester as an upgrade. To ensure that 4-wire resistance measurements remain accurate, CAMI recommends running the verification check every quarter. A 4-wire measurement module that is out of calibration will give inaccurate results. Some (maybe all) resistance measurements will be incorrect. Consequently, it may Pass what should Fail and, conversely, Fail what should Pass. In other words product yield will be contaminated due to unreliable measurements.
-
CB50 -
CAMI Research Inc. (CableEye®)
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently. Certain components within models M3U, M3UH, HVX, and HVX-21 (i.e. those capable of measuring resistance) are analog components whose characteristics change slightly over time. This aging is a natural phenomenon common to all electronic components and may cause resistance measurements or gradually deviate from normal. A tester that is out of calibration will give inaccurate results. Some (maybe all) resistance measurements will be incorrect. Consequently, it may Pass what should Fail and, conversely, Fail what should Pass. In other words product yield will be contaminated due to unreliable quality.
-
Pickering Interfaces Ltd.
The 68 Pin 1.27mm Pitch Micro-D Connector is used on high-density PXI modules that require 1A current rating and voltage handling up to 150Vdc.
-
Pickering Interfaces Ltd.
The 25 Pin 1.27mm Pitch Micro-D connector range is used on high-density applications including Pickering’s LXI DIO/Trigger port.
-
NLINE-UA429 -
Alta Data Technologies LLC
NLINE-UA429™ is an innovative product of ARINC operations for USB connections, ideal for in-field applications or point-point lab usage.
-
72-9170 -
Tenma
Quickly identify wires and tests continuityFits in any pocket or tool kit Invaluable in all audio, video, network, telecom and electrical installations
-
PHCT55 -
Pyle Audio Inc.
The PHCT55 is a two-piece item that tests telephone wire continuity. Play a test tone on one end and listen on the other, judge continuity, and diagnose break points.