Showing results: 2746 - 2760 of 5237 items found.
-
A694 -
AGM Elettronica
The A694 is a short circuit locator designed for fault location in metallic cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A694 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 0.1 ohm and less than 40 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
Wuhan Sunma Technology Co., Ltd.
Fiber Optic Splice Closure is a fiber management product typically used with outdoor fiber optical cables. It provides space and protection for the fiber optic cable splicing and joint. Fiber splice closure is used for aerial, strand-mount FTTH "tap" locations where drop cables are spliced to distribution cables. SunmaFiber supplies two types of fiber splice closures which are the horizontal (inline) type and the vertical (dome) type. Both are made of excellent engineering plastics to be waterproof and dust proof. And with various ports types, they can fit different fiber optic core numbers. More details about splice closure.
-
28063 -
Parallax Inc.
The SF45/B is the world’s smallest, lightest, scanning microLiDAR™. This 5 Hz oscillating sensor is highly configurable, with the ability to scan to 320°. Included in the box: SF45/B LiDAR sensor, a communications cable, a USB to micro-USB cable and five screws, and 5 nuts.
-
Elcometer Limited
Supplied with either standard cables or armoured metal reinforced heavy duty cables, Elcometer surface profile probes are supplied with a glass zero tile, calibration test foils (nominal values 125μm (5.0mils) & 508μm (20mils)) and an Elcometer test certificate.
-
Banair
The level of sophistication of the cable harness tester required will depend on the product type, failure modes and integrity required by the eventual customer. There are 3 main types of test that can be applied and this will determine which of our cable harness testers will be most suitable for your product.
-
SN5-TOMBAK -
ELMA Electronic, Inc.
The SN5-TOMBAK is a peripheral slot card for CompactPCI® Serial systems, with a dual port 10Gbps Ethernet controller. Both ports are available via SFP+ front bezel connectors for optical cables via SFP+ transceivers or SFP+ twinaxial copper cables.
-
FLL222 -
Fifo Electronics
The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.
-
Neuron System -
East Photonics, Inc.
Integrated management: Displaying current status of optical cable installation and location of fault using GIS - Facility management: Establishment of database as to the information of such physical communication facilities as communication device, cable, manhole, and telephone pole.- Recovery management: Enabling quick recovery by sending maintenance personnel to exact location in the event of fault.- Preventive management: Providing preventive measure against fault by prediction of fault due to heat deterioration of optical cable.
-
CAES
CAES offers a full range of cable assemblies for commercial aviation systems.
-
#TCA015 -
NSI Industries
24 inch cable assembly 8-Way alligator clips to RJ45, 849160008392
-
40-960-008-M -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
40-960-008-F -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
40-960-004-M -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
40-960-004-F -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
92-960-008-F -
Pickering Interfaces Ltd.
This connector is designed to allow users to directly terminate a cable with soldered connections.