Showing results: 2971 - 2985 of 5237 items found.
-
92-960-020-10A-M -
Pickering Interfaces Ltd.
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
92-960-020-16A-F -
Pickering Interfaces Ltd.
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 14 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
92-960-020-16A-M -
Pickering Interfaces Ltd.
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 14 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Distributed DAQlink4 -
Seismic Source Co.
The Distributed DAQlink 4 System is the combination of a standard DAQlink 4 seismograph and internal, high-speed, network extenders. Using inexpensive twisted pair telephone cable, these network extenders will send triggering times and receive seismic data from other DAQlinks. These cable links can send reach 10,000 ft, or three kilometers in length.
-
ARC Technology Solutions
Leverage ARC to Complete Your Next Complex Board and Cable Assemblies ProjectARC has the ability to build up CCAs, install components at the module level and build up sophisticated wiring and cable assemblies. We know what it takes, because we use this for our own manufacturing for complex, high-mix product builds.
-
DP750-100 -
Shenzhen Micsig Instruments Co., Ltd.
*The leads and probe are with shielded design, interface ends are integrated in a compact box, no need to twist the cables, leads to a lower noise floor and has less interference. *Support one-press Zero calibration and automatic overrange alarm.*Directly powered by Micsig UPI interface, realise auto scaling setup, can also powered by oscilloscope via USB cable.
-
Model No. 200-04 -
Srico, Inc.
SRICO Model No. 200-04 Photonic Electric Field Sensor System has the ability to measure electric field with minimal disturbance to the field. The lightweight fiber-optic cables allow for easy placement of the E-field probe, allowing it to be unencumbered by the use of heavy coaxial cables that may disturb the field being measured. The dielectric E-field probe is electrically passive.
-
YAV90Q04 -
6TL Engineering
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
Shanghai Himalayal Co.
Diagnostic test that indicates the degree of cable insulation degradation. Rather than using only a VLF instrument to perform a go/no-go proof test, the Tan Delta, used in conjunction with a VLF hipot, permits the user to grade the deterioration level of many cables in order to prioritize replacement, rejuvenation, or to determine what additional tests may be useful.
-
Monitran Ltd.
Proximity sensors work on the eddy current principle. A proximity system consists of an eddy current probe, extension cable and driver. A high-frequency RF signal is generated by the driver, sent through the extension and probe cables and radiated from the probe tip. The tip consists of a precision wound copper coil inside a chemical and temperature resistant PEEK case.
-
Weshine Electric Manufacturing Co., Ltd
Transformer iron core grounding current tester is a high-precision clamp meter specially designed for measuring AC leakage current, current and voltage. Large diameter (80×80mm) can clamp φ80mm cable, or 96mm×4mm flat steel ground wire, suitable for cables Leakage detection and transformer grounding flat steel leakage measurement.
-
M-HD-360A -
Fuzhou Metricu Technology Co Ltd
Analog camera testHD-TVI camera test, HD-CVI camera test, AHD camera testDC12V 1A power outputVGA input, support 1920 x 1200P 60FPSAuto HD, auto recognize HD coax camera type and resolutionUTP cable test, detect the near-end, mid-end and far-end fault point of the network cable crystal head
-
SPM-50 -
ShinewayTech
SPM-50A Spectrum Power Meter brings innovative testing concept and approach for RF cable system installation and maintenance. It combines the key function of spectrum analyzer and power meter, designed to measure the power characteristics of particular signal among mixed signals transmitted on cable, fast and accurately present result in power histogram or spectrum chart.
-
Digital -
Langer EMV-Technik GmbH
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
Wabtec
Cable reels & slip ring assemblies for reliable power and data transfer in mining, construction and material handling applications.