Showing results: 3091 - 3105 of 5237 items found.
-
PD-TaD 60 -
BAUR Prüf- und Messtechnik GmbH
The PD TaD 60 portable PD Diagnostics system is used in combination with a BAUR VLF generator frida for carrying out partial discharge measurement and location.* Comprehensive 360° cable analysis – with parallel partial discharge and dissipation factor measurement* Time-optimised and safe cable condition evaluation* The lightest and most compact PD measuring device up to 60 kVpeak* Developed for portable use on site
-
40-967-160-F -
Pickering Interfaces Ltd.
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination and provide a suitable method of restraining the cables. Pickering cable assemblies for this product are contained elsewhere in this data sheet. Interfacing PCB?s should be designed with suitable clearances for the voltage the application requires.
-
40-967-160-M -
Pickering Interfaces Ltd.
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination and provide a suitable method of restraining the cables. Pickering cable assemblies for this product are contained elsewhere in this data sheet. Interfacing PCB?s should be designed with suitable clearances for the voltage the application requires.
-
92-965-025-M -
Pickering Interfaces Ltd.
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Extech MA3110 -
Extech Instruments Corporation
Flexible 11" (28cm) clamp jaw easily wraps around bus bars and cable bundles that may be difficult to access with regular clamp meters. The thin 8mm cable diameter easily fits into tight spaces. Includes test leads for multimeter functions measuring Voltage, Resistance, and Capacitance. True RMS and CAT IV rated allows for maximum accuracy and safety for your measurements.
-
DCSS502BC -
Sanshine Electronis Co., Ltd.
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
Megger Group Ltd.
Locating high and low impedance faults on paired metallic cables is a crucial yet often difficult task for a telecoms engineer. Megger designs TDRs specifically for the communications industry, which makes each unit a safe, application specific tester that can be used on virtually all communications cable types. The wide range of TDRs makes it easy to choose the tester with the resolution and range you need.
-
N1410A -
Keysight Technologies
The N1410A is a starter kit for B2985B and B2987B Electrometer/High Resistance Meter and includes N1414A High resistance measurement universal adapter and N1415A Triax to alligator cable. The N1414A helps you setup the cables and makes the cabling setup easier. The N1415A is recommended to measure more than 1 nA current, but you can probably measure less than 1 nA current with appropriately shielding.
-
410104273 -
Virginia Panel Corporation
This G6 ITA is equipped with a removable EMI-shielded backshell. This backshell slides up to provide access to wires and connectors. This ITA also includes a keying feature. Removable and adjustable U-shaped cable clamps are attached by screws to the ITA frame and allow ITA modules to be pre-wired before assembly. The clamps can hold cable bundles with an oblong bushing effective diameter of 1.59". ITA strain relief plates are not needed.
-
Paula -
BAUR Prüf- und Messtechnik GmbH
BAUR paula phase detector. The paula phase detector is used for clear phase identification in earthed and shorted medium and high-voltage cables. With the help of the measurement procedure tried and tested over many years, paula delivers precise phase allocation without scope for interpretation and corresponds to the highest safety standards for tasks on and close to electric equipment.* Clear phase determination possible in cable lengths up to 40 km* Highest level of safety when used on earthed and shorted cables in compliance with EN 50110-1 (DIN VDE 0105-100)* Suitable for all switchgear constructions due to compact design of the signal injectors* Ready for operation for up to 2 weeks (standby mode)
-
S Series -
Com-Power Corporation
The S series CDNs are for shielded cables with single or multiple conductors. These CDNs are supplied with professional audio (RCA), D type and Centronics connectors.
-
Sy629PMC-M-CMC -
Sycos AES
The Sy629PMC-M-CMC module allows ARINC-629 terminals to communicate directly without the need for an ARINC-629 bus Cable and conventional Current Mode Couplers.
-
Sy629PCIe-M-CMC -
Sycos AES
The Sy629PCIe-M-CMC module allows ARINC-629 terminals to communicate directly without the need for an ARINC-629 bus Cable and conventional Current Mode Couplers.
-
Axiomtek Co., Ltd.
Axiomtek provides KVM solutions for centralized management, keyboard drawers, keyboards, track balls, slide rails, CD-ROM's, cables and much more.
-
Axiomtek Co., Ltd.
PoE-PSE I/O boards comply with IEEE802.3af standard via an internal cable connected to LAN port on a SBC to power an external PoE device