Showing results: 4126 - 4140 of 5237 items found.
-
Bloomy Controls, Inc.
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
Teledyne RF & Microwave
Gain Shape Linearizer Amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run, or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Extech 401014 -
Extech Instruments Corporation
401014 is a Big Digit Thermometer that simultaneously displays indoor and outdoor temperatures. Its waterproof sensor for outdoor measurement extends on a 9.6 ft. thin cable for easy installation. Internal memory stores Min/Max readings over time. Thermometer comes complete with built-in stand, external temperature sensor, AAA battery, and wall mount bracket.
-
Extech TL620 -
Extech Instruments Corporation
The Extech TL620 is a 200 MHz, 10:1 Oscilloscope Probe with a 1.2 meter cable. It features a 10 M ohm input impedance, 20 pF Capacitance, max voltage of 600 V, and 15 pF to 40 pF compensation range. Includes probe tip, ground lead, marker ring, sprung hook, and adjustment tool.
-
Extech 380562 -
Extech Instruments Corporation
Compact and precise, the Extech 380562 Milliohm Meter has 7 ranges and measures down to 0.01mΩ using 4-wire Kelvin clip test leads. Measurements are displayed on the unit's large 0.8", 1999-count LCD. Built-in comparator for Hi/Lo/Go resistance testing or selection. Complete with 4-wire cables with Kelvin clip connectors and power cord.
-
GPIB -
Test Electronics
Test Electronics will customize the TE3000 GPIB signal routing box for your test application. Then, you simply rack and stack all the equipment, cable all the switched signals to the back of this GPIB box, add a rack mount computer, plug in the National Instruments GPIB board and software. Then run your customized GPIB based test system.
-
F9 Systems, Inc.
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
Omron Industrial Automation
Save panel space and simplify design of external I/O blocks for PLCs and other controllers with plug-in relays. PLC interface adapters and pre-terminated cables reduce installation time and labor connecting to Omron and Siemens PLC I/O modules, and to network interfacing slice I/O systems. The relay is the perfect choice for panel builders and industrial controls designers.
-
360 DSP -
Trilithic Inc.
The 360 DSP is a next generation fulfillment meter specifically tailored for installation and troubleshooting. The 360 DSP is part of a system consisting of the meter, ViewPoint software, and means for acquiring information from the Cable System's Workforce Management application.Upstream Return Spectrum Analysis (4 to 110 MHz). Level Mode. C/N Measurement. QAM mode (MER/BER/Constellation).
-
SBL SERIES -
Transducer Techniques, Inc
The SBL Series heavy duty shear beam load cells are ideal for process weighing and for use in low profile industrial scales. These economical load cells are easy to install and durable in the field. Environmental protection is afforded through water resistant potting, a compression sealed and strain relieved cable entry, and corrosion resistant nickel plated steel.
-
JT 2135 -
JTAG Technologies Inc.
The JT 2135 allows TAP signals to be extended away from the base JT 2137 (classic pod) by up to 1 meter and retain full pod’s frequency specifications. The active circuitry inside the JT 2135 compensates for the TDO signal return time of the longer interface cable. Multiple JT 2135s can be implemented if a longer extension is required.
-
Teledyne Defense Electronics
Gain Shape Linearizer Amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run, or perhaps changing the input gain response to an MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
FExx Series -
Rohde & Schwarz GmbH & Co. KG
R&S®FExx external frontends extend the frequency ranges of Rohde & Schwarz signal and spectrum analyzers and signal generators up to 170 GHz. The R&S®FExx enables the up and down-conversion of the signal directly at the DUT. In an OTA environment it lowers cable losses, increases sensitivity and delivers more power at the antenna.
-
779501-01 -
NI
MXI-Express Interface, PXI Remote Control Module—The PXI‑8360 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8360 through a copper, x1 MXI‑Express cable.
-
777101-01 -
NI
50-Pin Male IDA to 50-Pin, Female Screw Terminal, Panel Mount Terminal Block - The CB-50LP provides 50 screw terminals for connection to I/O signals from 50-pin NI data acquisition devices. The CB-50LP includes one 50-pin header for direct connection to 50-pin cables and metal standoffs for use on a desktop or for mounting on a custom panel.