Showing results: 736 - 750 of 5237 items found.
-
-
-
E1739D -
Keysight Technologies
The E1739D 25-meter (82 feet) Sensor Cable is used to connect E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.
-
Teledyne Marine PDS
- Accurate and reliable- Maximum use of engineering preparation- Visualise the cable lay process in 3D, top, and profile views- Different routes for vessel and pipe- Automatic dog legs guidance at the end of the cable- Computed cutting points are shown- Optimum control of your project
-
ProDAQ 8034 -
Bustec Ltd.
The ProDAQ 8034 PCI Express x4 copper cable connects crates equipped with the ProDAQ 3026 Low-Cost PCI Express VXIbus slot-0 interface or the 3030 PCI Express VXIbus slot-0 interface to the ProDAQ 3261 PCI Express host interface. The cable transmits four PCI Express lanes and sideband signals with transfer rates of up to 10 Gbps full-duplex. The robust, shielded cable and the die-cast connectors with latching mechanism ensure a stable connection and prevent accidental disconnects.
-
784184-100 -
NI
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
784184-50 -
NI
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
OMK-SR-MCS -
OPTOKON a.s.
The OPTOKON OMK-SR-MCS Mini cable splice tool kit offers all necessary tools and components for field usable, quick repairs of cables in the toughest of environments. Utilising the proven mechanical splice in both singlemode and multimode applications, there is no need for power, heat or complicated termination procedures. Based on standard mechanical splice technology of the MCS-04, the tool kit provides low loss fiber jointing in just a few minutes. Cable retention and tie off is achieved through the aramid yarn and IP 67 guaranteed in the same way as connectors. With a small diamensions the Mini Cable Splice provides a permanent join of ruggedized cables up to 4 fibers. Purchased with all the tooling and consumables necessary to carry out the operation, the kit comes complete with splice unit, ready for use in a rugged field usable carry case. Splice unit, spares and consumables are then replaced and replenished at a low cost whenever necessary.
-
EE105T-xx -
Executive Engineering
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
Y1218A -
Keysight Technologies
The Y1218A is a cable tray kit designed for the M9018B and M9019A. It can be used with both the rack mount kit and the rail kit but, the rail kit is not required. The kit includes a cable tray, feet for using the chassis on a table, and attachment hardware. An M9018B or M9019A that is racked using the cable tray uses 5U of rack space. The tray is compatible with the Y1217A Rack Mount Rail Kit, the Y1215B/C Flush Mount and Y1216A/B Recessed Mount Rack Adapter kits. This tray is not compatible with the Y1270A Front Panel Interfacing Kit.
-
Y1200B -
Keysight Technologies
Connect an M9502A/M9505A AXIe chassis or M9018A PXIe chassis with M9021A cable interface to a laptop computer
-
Y1135A -
Keysight Technologies
Connect this M/F twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
Pickering Interfaces Ltd.
The cable assemblies below are suitable to use with Pickering cards and modules that utilize a GMCT RF connector.
-
Multidyne
Sometimes you just want to connect everything at once. Recognized worldwide as a leading supplier of fiber-optic solutions, MultiDyne now operates a full-service cable fabrication lab. Our rigorous in-house qualification and testing processes bring greater quality control to our product manufacturing workflow. As a Neutrik COCA member, MultiDyne is one of the few certified assemblers of ruggedized opticalCON hybrid fiber cables. MultiDyne also terminates SMPTE 304M LEMO connectors and offers other tactical cables that easily mate to SMPTE fiber-optic cameras, standard breakout boxes, and our other fiber-optic transport solutions. With all assembly happening in-house by specialized technicians, customers can purchase all components of a complete MultiDyne fiber transport solution - or new cables and assemblies to upgrade existing fiber systems.
-
KI-TK872 -
Kingfisher International
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.