Filter Results By:
Products
Applications
Manufacturers
-
product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Cut Ends, 2m
A025DF4-C-0A200
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Cut Ends, 1m
A025DF4-C-0A100
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Tinned Ends, 0.5m
A025DF4-T-0A050
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Tinned Ends, 1m
A025DF4-T-0A100
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Tinned Ends, 2m
A025DF4-T-0A200
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m
A025DM5-C-0A050
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Cut Ends, 1m
A025DM5-C-0A100
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Cut Ends, 2m
A025DM5-C-0A200
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m
A025DM5-T-0A050
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Tinned Ends, 2m
A025DM5-T-0A200
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Tinned Ends, 1m
A025DM5-T-0A100
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Terminal Block For 34925A Multiplexer
34925T
The Keysight 34925T is a terminal block for the 34925A 40/80-channel FET multiplexer, used for discrete wiring. It supports up to 20 AWG wire size for up to 100 connections or 24 AWG for 100 connections or more. Two terminal block options facilitate wiring connections to the 34925A module.
-
product
Multi-channel IP Receiver
WDJS-3
WDJS-3 is the latest time-domain induced polarization receiver, working with short lead wire. In operation, a WDFZ-5T or WDFZ-10T series high-power intelligent transmitter may be the power source and several receivers could work simultaneously; what's more, the receiver can measure with several channels, which multiples the working efficiency.
-
product
Automatic Upset Testing Machine
YQA Series
Jinan Testing Equipment IE Corporation
This kind of machine is designed according to the International standards EN 10263-1:2001 “Metallic materials upset test methods”, especially for the quality inspection of high-speed rods and wires. Through simulating the quick press conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. This kind of machine is widely used in the steel industry, standard samples manufacturing industry, and tools manufacturing industry, for the inspection of the metallic materials upset tests. Under the room temperature or the hot conditions, exert test force on the direction of specimen axial line, quickly compress the specimen, and then inspect the metal ability of bearing upset deformation in the specified upset ratio. It also can show the metal surface disfigurements.
-
product
Guided Assembly | Cable Harness Testers
Autobuild™ Software
CAMI Research Inc. (CableEye®)
Our optional, add-on AutoBuild™ software (Item 728) offers Guided Assembly for cables and wire harnesses. Use a supplied probe, or a finger with wrist strap, to touch an unterminated wire and the software shows (and says) exactly where the wire should be connected. As the operator attaches each new wire, AutoBuild checks the entire assembly and provides a clear checklist showing all completed good connections. When using our resistance-capable testers, you may connect diodes and resistors by name and value, check resistance values over the tester's specified range, and test conduction and isolation resistance against specified thresholds. Programmable tones accompany the graphic screen to give clear signals to the operator when good connections are completed or when incorrect connections, resistance violations, or diode insertions are detected. Combine with our Light Director™ option for light-guided assembly.
-
product
Loop Meter
MZC-304
# Measurements of impedance in a short circuit loop.- L-PE circuit,- L-N, L-L circuit,- L-PE(RCD) circuit - without tripping the circuit breaker > 30mA.# Low voltage resistance measurement:- continuity measurement - DC current +200mA with wire resistivity reset- low current resistance measurement with accoustic signalling,
-
product
Advanced Diagnostic Load Cell Tester
LCT-U
The Advanced Diagnostic Load Cell Tester Model LCT-U is a stand-alone hand-held device specially designed for fast, comprehensive troubleshooting of strain gauge load cells. The LCT-U can quickly diagnose problems with all common types of load cell available today, including 6-wire load cells (with sense wires).
-
product
Cable Assembly, 160-Pin DIN41612, Female to Female, 0.5m, 45º
A1604F5-1604F5-0A050
For applications where a 45 degree cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
product
Cable Assembly, 160-Pin DIN41612, Female to Female, 1m, 45º
A1604F5-1604F5-0A100
For applications where a 45 degree cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
product
Cable Assembly, 160-Pin DIN41612, Female to Female, 2m, 45º
A1604F5-1604F5-0A200
For applications where a 45 degree cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
product
Cable Assembly 44-Pin D-Type Female to Unterminated With Tinned Ends, 2m
A044HF4-T-0A200
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly 44-Pin D-Type Male to Unterminated With Cut Ends, 2m
A044HM5-C-0A200
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Unterminated (Tinned Ends), 1m
40-972B-200-1m-MU
This male rear exit to unterminated 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50 wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to the product by screwlocks.
-
product
32-CH Discrete Output Modules with U Profile
HSL-DO32-UD
*UD type is suitable for screw type wiring. Each wire to sensors or actuators can be fixed by the screw terminal*RJ-45 phone jack for easy installation*Compact and single board design to meet space limitation and cost-effective requirement*Support 32 DO channels*Transmission speed: 3/6/12 Mbps
-
product
Battery Powered Milliohm Meter - High Accuracy, High Resolution Portable Milliohm Meter for Field Use
Extech 380580
Extech Instruments Corporation
The 380580 is a Battery Powered Milliohm Meter. This milliohm meter features a high accuracy, a high resolution, portable milliohm meter battery operated for field use, four terminal Kelvin measurements, and Over-temperature and over-voltage protection. CE certified. Complete with 8AA batteries, and 2 sets of test leads (4 wire with 4 alligator clips and 4 wire with 2 Kelvin alligator clips).
-
product
PXIe-2526 , 158‐Channel, 2 A PXI Multiplexer Switch Module
780587-26
158‐Channel, 2 A PXI Multiplexer Switch Module—The PXIe‑2526 is a high‐density PXI multiplexer switch module that is ideal for routing signals within automated test systems. It uses electromechanical relays to perform immediate switch operations in either a 158x1 1‑wire or 79x1 2‑wire multiplexer topology. The PXIe‑2526 also features onboard relay counting for relay monitoring.
-
product
Cable Continuity Tester, Auto Ranging, 4000 Count Display
72-9170
Quickly identify wires and tests continuityFits in any pocket or tool kit Invaluable in all audio, video, network, telecom and electrical installations
-
product
LAN Cable Tester
21-8569-00
Open / Short / Misswiring test?BNC / RJ45 each pin connected display?No wire or termination?Isolation Resistances 50K ohms test
-
product
Ribbon cable headers
HDRterm50
Ribbon cable headers are commonly used with IP compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The HDRterm50 converts from 50 pin ribbon cable to a 50 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.
-
product
Ribbon Cable Headers
DINterm64
Ribbon cable headers are commonly used with VME compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The DINterm64 converts from 64 pin ribbon cable to a 64 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.