Showing results: 136 - 150 of 199 items found.
-
GX5292e -
Terotest Systems Ltd.
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
40-131-201 -
Pickering Interfaces Ltd.
These are low cost, general purpose electromechanical relay cards capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
40-131-001 -
Pickering Interfaces Ltd.
These low cost, general purpose electromechanical relay cards are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 pin D-Type connector plug.
-
40-157-001 -
Pickering Interfaces Ltd.
40-150/151 modules have 8xDPST or 12xDPST power relays, suitable for switching inductive/capacitive loads up to 5A at 250VAC. 40-155/156 modules have 8xSPDT or 16xSPDT power relays and 40-157 is configured as 8xDPDT. Power relay modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids. The 40-150 series of power relay module are suitable for applications requiring switching of either mains voltage or DC current.
-
EIM-01 -
Compact Power Company
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
NI
PXI DeviceNet Interface Modules have an onboard microprocessor and optically isolated physical layer to communicate with a DeviceNet network system as a master (scanner) or slave device. The modules ship with a high-level API that provides complete access to a DeviceNet network and features easy access to device data and streamlined explicit messaging. PXI DeviceNet Interface Modules are ideal for prototyping DeviceNet systems, PC-based control, embedded control systems, PC-based human machine interface (HMI), and DeviceNet network management utilities.
-
GX5290 -
Terotest Systems Ltd.
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Datexel
Datexel has a range of Modbus RTU Masters, Slaves, Controllers, Data Loggers and Modbus remote displays. The DAT9000 is a Modbus RTU Master with RS485, RS232 and Ethernet Interfaces. The DAT9000IO is similar to the DAT9000 but it has digital input and outputs. The DAT9000DL has an additional Data Logging facility and the DAT9000DLIO has both Data Logging and digital IO. The DAT9011 is a Modbus Master with 2 analog inputs which can chose from Thermocouple's, RTD's, Potentiometers, mA and mV's. It also has 2 outputs which can be mA or voltage. The DAT9011 can also accept digital inputs and provide 2 SPDT relay outputs. The DAT9011DL also has a Data Logging facility which can store up to 8gb of readings on a thumb drive.
-
e-CAM31_MI0330_MOD -
e-con Systems Inc.
e-CAM31_MI0330_MOD is a high performance, small form factor, 3.4 MP Autofocus Low Light Camera Module with Liquid Lens. It is based on AR0330 CMOS Image sensor from ON Semiconductor®. This Autofocus Liquid Lens Camera Module has slave mode for precise frame-rate control and for synchronizing two sensors. e-CAM31_MI0330_MOD – Liquid lens camera module has superior low light performance. It supports Full HD @ 60fps for maximum video performance. It also has a support for external mechanical shutter and an on-chip phase-locked loop (PLL) oscillator. The dedicated ISP performs the entire Auto functions like auto white balance, auto exposure control in addition to complete image signal processing pipeline.
-
NI
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
Model 9099 -
ICS Electronics
* Use Modbus TCP/IP, VXI-11, or Raw Sockets (Telnet) or to control Modbus RTU slave devices.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Interfaces with PLCs or any Modbus TCP/IP Controller.* Fully VXI-11 compliant.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the Modbus network or devices.* 9099 is a 2x to 5x faster than the 8099 and includes a new Modbus device control page.
-
Aidiga Ltd.
Sampling frequency: 8 000 - 192 000 HzVertical resolution: 16 bitSound card selection: YESChannels count: 2Channels modes: independent, I master - II slave, II master - I slaveMath: Ch1=Ch1+Ch2; Ch1=Ch1-Ch2; Ch2=Ch2+Ch1; Ch2=Ch2-Ch1Signal reconstruction: YESPretrigger: YESTrigger events: above, below, free runInternal trigger: YESExternal trigger: two channel mode - NO, single channel mode - YESData visualisation modes: single, continuous displayFFT points count: 8 - 2 097 152FFT Window functions: Rectangular, Gauss, Hamming, Hann, Bartlett, Triangular, Bartlett-Hann, Blackman, Nutall, Blackman-Harris, Blackman-Nutall, Flat TopOscilloscope amplitude axis units of measurement: Volts (nV...kV), Sample Value (smp)
-
40-132-202 -
Pickering Interfaces Ltd.
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
40-132-101 -
Pickering Interfaces Ltd.
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
40-132-102 -
Pickering Interfaces Ltd.
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.