Showing results: 91 - 105 of 427 items found.
-
-
MultiDimension Technology Co.,Ltd.
Magnetic gear tooth sensors utilize a unique push-pull Wheatstone bridge design, including one or two Wheatstone full bridges, with four or eight unshielded high sensitivity TMR sensing elements. The Wheatstone bridge creates a differential voltage output with respect to the magnetic field gradient along the sensor’s sensitive direction.
-
5093 -
Abaco Systems Inc
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
CAEN S.p.A.
VME / Optical Link / USB and Ethernet Bridges
-
MultiDimension Technology Co.,Ltd.
AMR linear sensor utilizes two push-pull Wheatstone bridges each composed of four highly sensitive AMR sensor elements. These Wheatstone bridges effectively compensate the sensor’s temperature drift to achieve outstanding temperature stability with minimal noise.
-
XM26001 -
LinkedHope Intelligent Technologies Co.,Ltd.
XM26001 is a graphics, image processing and computing single-board computer independently developed by Linghao Intelligent®. It uses the AMD G series APU GX-210HA by default, integrating the CPU, GPU, south bridge and north bridge on one silicon chip.
-
PCI EmbeddedComputer Systems
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
Procter & Chester Measurements Ltd
Radio Telemetry: A transmission of data from a remote source via a radio to a receiving station for recording and analysis. Inductance: A contactless method of supplying power to (in this case) a strain gauge bridge. The signal is then transmitted back to the electronics. Slip Ring: Consists of a conductive band mounted on a shaft and is insulated from it. The wheatstone bridge is connected to the bands (usually four off). Fixed brushes or contacts make contact on to the bands to transfer power to the bridge and signal back to the static instrumentation.
-
TEGAM Inc.
Ratio Standards by Tegam including ratio transformers, synchro-resolver bridge, synchro-resolver standard
-
cPCIBPMC3U64ET -
Dynamic Engineering
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
PMT20010 -
Power Measurement Technologies Inc.
The PMT20010 Comparator is an automatically balancing bridge that measures the accuracy of instrumentation potential and current transformers.
-
MultiDimension Technology Co.,Ltd.
Linear sensor utilizes a unique push-pull half bridge composed of four unshielded TMR sensor elements. The unique bridge design provides a high sensitivity signal output that is linearly proportional to a magnetic field applied parallel to the surface of the sensor package, and it provides superior temperature compensation of the output.
-
SD-31 -
Potomac Instruments, Inc.
The Model SD-31 Synthesizer-Detector is a high output crystal signal generator of precisely known frequency combined with a sensitive, selective detctor for RF bridge measurements of AM antenna impedance. Packaged in a single light-weight battery-powered unit, the SD031 complements bridges such as the General Radio 1606, 916, and the Delta OIB-1.
-
5085 -
Abaco Systems Inc
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
785840-01 -
NI
96-Pin Female DIN to 10-Pin Female RJ50, Rack Mount Terminal Block - The RM-24999 provides RJ50 connectivity in a 1U rack-mount form factor for up to three bridge input modules. You can use SH96F-96M-5 Sensor Cables to connect to the PXI Express bridge input modules.