Showing results: 376 - 390 of 751 items found.
-
MS 1720 -
Meltronics Systemtech
PCI to CPCI Extender card is used for extending the standard desktop PCI bus to compatible CPCI bus. This will help to test all the CPCI and PXI cards without having a CPCI or PXI backplane. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the CPCI and PXI boards.
-
ProDAQ 8036 -
Bustec Ltd.
The ProDAQ 8036 LXI trigger bus cable connects the ProDAQ 6100 LXI function card carrier or the 3030 PCI Express VXIbus slot-0 interface to any device equipped with LXI triggers. The robust, shielded cable and the die-cast connectors ensure a stable connection and prevent accidental disconnects.
-
SMT-FMC211 – LPC -
Sundance Multiprocessor Technology Ltd.
The main component of the SMT-FMC211 is the Texas Instruments 4 channel DAC – TI’s Quad 1.25GHz DAC3484. This device offers excellent SFDR performance better than 70dBc, with an output sample rate of over 312MSPS. It interfaces to an Artix-7 XC7A15T-2C FPGA using a 16 bit differential DDR bus.
-
DP-OBC-3003 -
Data Patterns Pvt. Ltd.
DP-OBC-3003 is a rugged 3U cPCI based board with 64 Digital Input channels in open/ground configuration and 4 serial ports of RS422 interface. It operates on 32-bit, 33MHz PCI bus. Four RS422 channels are incorporated with opto-isolated inputs which supports baud rates upto 115.2Kbps.
-
VM-DBA -
W-IE-NE-R, Plein & Baus GmbH
VM-DBA is a new test and diagnostic module for VME-bus systems which visualizes activities on all VME bus lines on the set of front-panel LEDs, but also allows one to digitize individual waveforms of all these lines into 2kBit -long storage memories, for a subsequent readout via VME or USB interfaces.
-
µPD720202 -
Renesas Electronics Corp.
µPD720202 is a USB host controller LSI compatible with the USB 3.0 and xHCI (eXtensible Host Controller Interface) 1.0 specifications. The system bus is compatible with the PCIe Gen2 specification. The controller provides two USB ports with LS (Low-Speed) / FS (Full-Speed) / HS (High-Speed) / SS (SuperSpeed) support.
-
µPD720201 -
Renesas Electronics Corp.
The µPD720201 is a USB host controller LSI compatible with the USB 3.0 and xHCI (eXtensible Host Controller Interface) 1.0 specifications. The system bus is compatible with the PCIe Gen2 specification. The controller provides four USB ports with LS (Low-Speed) / FS (Full-Speed) / HS (High-Speed) / SS (SuperSpeed) support.
-
W-IE-NE-R, Plein & Baus GmbH
The Mpod micro-1 crate is the smallest and low cost option for the WIENER multi-channel high and low voltage power supply system. The Mpod micro mainframe can house 1 plug-in low or high voltage modules. The integrated Mpod controller card provides10/100 Ethernet, CAN bus and USB-2 interfaces.
-
60-982-001 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
60-982-002 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
PGY-RFFE-EX-PD -
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
Model 58663 -
Pentek, Inc.
- Complete GSM channelizer with analog IF interface- Eight 180 MHz 16-bit A/Ds- Four banks of 375 DDCs for upper GSM band- Four banks of 175 DDCs for lower GSM band- PCI Express (Gen. 1 & 2) interface up to x4- LVPECL clock/sync bus for multiboard synchronization- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Model 57663 -
Pentek, Inc.
- Complete GSM channelizer with analog IF interface- Four 180 MHz 16-bit A/Ds- Two banks of 375 DDCs for upper GSM band- Two banks of 175 DDCs for lower GSM band- PCI Express (Gen. 1 & 2) interface up to x4- LVPECL clock/sync bus for multiboard synchronization- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Saint2 -
DG Technologies
Testing Interfaces for Multiple Simultaneous Serial Busses Extensive On-board Memory Capacity High-performance Infineon Micro-controller RS-232 and USB Interfaces for Communication with a Host Computer SAINT2 Hosts Software for Your PC User-configurable DB-25 Cable Optional Discrete I/O Add-on Daughter Board System Applications Product Development, Testing and Software Re-flash in One Device Bus Monitor 2 Message Filtering, Scripting, Emulation and Logging Scrolling Message Monitor SAINT Bus Engine Provides Open API for Software Applications Interfaces with USB/RS232 Create Your Own Plug-ins
-
Pepperl+Fuchs GmbH
The clear assignment of a signal to a terminal while maintaining the existing instrumentation and wiring is a major advantage of remote I/O . A second is the significantly reduced wiring through the use of a bus interface to the control system - remote I/O offers the best of two technologies and is therefore ideally suited for modernizing and expanding process plants.