Showing results: 2101 - 2115 of 2906 items found.
-
40-971B-200D-0.5m-MF -
Pickering Interfaces Ltd.
This male rear exit to D-type 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
40-971B-200D-0.5m-MM -
Pickering Interfaces Ltd.
This male rear exit to D-type 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
40-971B-200D-1m-MM -
Pickering Interfaces Ltd.
This male rear exit to D-type 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
40-971B-200-0.5m-MM -
Pickering Interfaces Ltd.
This male rear exit to ribbon cable 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
40-971B-200-1m-MM -
Pickering Interfaces Ltd.
This male rear exit to ribbon cable 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
40-971B-200D-2m-MM -
Pickering Interfaces Ltd.
This male rear exit to D-type 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
North Atlantic Industries
NAI offers, and continues to introduce, high density multifunction or combination-function I/O boards designed for a specific application or purpose. Based on the specialized application itself, from the interface connectors through the motherboard, to the specific function, these boards typically address I/O function integration challenges requiring higher current capacity, layout, and/or grounding requirements that are not available in our standard I/O boards. They are specifically designed for rugged defense, commercial aerospace, and industrial applications.
-
Teledyne LeCroy
The Teledyne LeCroy WavePulser 40iX and the Teledyne Test Tools T3SP15D are a perfect combination of complimentary products to serve the requirements on testing, validating and troubleshooting cables, backplanes, connectors, transmission lines on boards and interconnect.
-
VR300 -
Sundance Multiprocessor Technology Ltd.
The VR300 is a Test RTM, typically used during firmware and software development and debugging cycles on the VF360. The rear panel contains two mini-USB connectors, a Dual mini-SAS (SFF-8088) connector and a SFP case.
-
72-6290A -
Tenma
The 72-6290A is a multi-modular Cable Tester (LAN Tester) with LED meter display. Requires 9V battery for this modular cable tester. Used with RJ-45, RJ-12, RJ-11 connectors and USOC4, USOC6, USOC8 cables.
-
MS 1508 -
Meltronics Systemtech
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
SAMPULSE20x2 -
Furaxa, Inc.
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
GPSL18 -
INSTOCK Wireless Components, Inc
GPSL18 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while blocking the DC current path from both devices. Max voltage rating at the DC blocked ports is 10 VDC; maximum current rating is 50 mA. Furnished with SMA female connectors all ports. Being a "micro-sized" splitter, GPSL10 weighs only 21 grams and is suitable for applications requiring low-weight parts.
-
SEN-30003-K -
Playing With Fusion Inc
Breakout board for the MAX31855K digital thermocouple interface ICs by Maxim. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws.
-
SparkFun Electronics
The SparkFun MicroMod mikroBUS Carrier Board takes advantage of the MicroMod, Qwiic, and mikroBUS™ ecosystems making it easy to rapidly prototype with each of them, combined. The MicroMod M.2 socket and mikroBUS 8-pin header provide users the freedom to experiment with any Processor Board in the MicroMod ecosystem and any Click board in the mikroBUS ecosystem, respectively. This board also features two Qwiic connectors to seamlessly integrate hundreds of Qwiic sensors and accessories into your project.