Showing results: 2776 - 2790 of 2906 items found.
-
42-780B-553 -
Pickering Interfaces Ltd.
The 40-780B-553 (PXI) and 42-780B-553 (PXIe) are triple failsafe SPDT 50 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
W5643A -
Keysight Technologies
The W5643A DDR5 2-wing BGA interposer for DDR5 x4/x8 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A. The W5643A is the smallest BGA interposers for DDR5 x4/x8 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding up to 5GT/s for protocol analysis and up to 4Gb/s for DQ capture. U4208A and U4209A probe/cables connect any W5643A DDR5 BGA interposer directly into the U4164A logic analyzer module using 61-pin high density zero insertion force (ZIF) connectors that attach to the W5643A BGA interposer wings.
-
42-780B-524 -
Pickering Interfaces Ltd.
The 40-780B-524 (PXI) and 42-780B-524 (PXIe) are quad failsafe SPDT 18 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
34937A -
Keysight Technologies
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
MS 1121 -
Meltronics Systemtech
Portable test equipment to check the electrical functionalities of pylons by simulating various store types in aircraft. This system is able to simulate the functionalities of different PIBs (IB/MB/CF, OB & Laser). The system provides facility to test two Pylons in parallel. The tester provides aircraft specific AC &DC voltages and facility to inject discrete inputs for checking output(s) viz firing voltages, fusing voltages. The system provides four channels of RS422 and Two channels of 1553B communication. Portable unit with caster wheels with all required hardware, power supplies, instruments, connectors and laptop housed in it.
-
Efield AB
Efield® offers a complete and unique integrated modelling and simulation environment for 3D analysis of a wide range of electromagnetic applications such as: Antenna design All kind of antennas including horn, reflector, wire and microstrip antennas as well as broadband antennas and antenna arrays. Antenna integration Radiation pattern of installed antennas on large platforms such as aircraft or ships. Coupling between installed antennas. Microwave design Typical applications includes design of filters, connectors and couplers. EMI/EMC interaction Analysis of a wide range of EMC/EMI problems including shielding and coupling. Scattering & radar cross-section RCS analysis of structures such as aircraft, ships, air-intakes, exhausts, and antennas.
-
AD14-65Mx16AVE -
Ultraview Corporation
14-bit 16-concurrent channel 65MSPS A/D board for demanding large-system uses, where signals on multiple time-aligned channels need to be observed with high SNR, such as RADAR, nuclear instrumentation, ultrasound, medical imaging, spectroscopy, communications systems, RF component and antenna testing and other critical applications. An on-board low-jitter LMX2581-based RF synthesizer allows any A/D sampling rate between 20MSPS and 65MSPS to be specified in software. A second on-board LMX2581 with synchronized reference can be optionally used to output four stimulus clocks on SMA connectors that can be vectored to any combination of 4 external transmitters, microwave pulse generators, laser modulators, and other devices.
-
Meritec
Meritec's 1MM Slot Test Connector was developed to eliminate many of the common problems associated with using a standard connector in a test application. When testing, the PCB is plugged in and out of the connector many times. The wiping action that occurs between the contacts and the board starts to wear down the plating on the contacts and the plastic housing itself.At some point in time the connector becomes a liability and can no longer be considered reliable. The standard connectors being used today for test applications have a life cycle of 250 to 500 (the number of insertion and withdrawals applied to the connector). Meritec's Slot Test Connector has a life cycle greater than 100,000!
-
Analog Devices Inc.
Analog Devices Car Camera Bus (C2B™) is an innovative new camera link technology enabling HD video over Unshielded Twisted Pair (UTP) cables and unshielded connectors. C2B provides an easy upgrade path from SD to HD cameras without the need to change the existing cable and connector infrastructure. C2B enables a camera link with reduced system cost, significant weight savings and increased robustness. The C2B portfolio of transmitter and receiver devices enable seamless camera connectivity in the vehicle. The C2B technology was defined and designed for automotive applications and provides a robust camera link solution for these applications:
-
Dynamic Test Solutions
DTS Package Test (DIB) loadboards are designed to specific devices and configured for both hand test and fully automated handler applications. DTS loadboards incorporate any brand of socket or contactor and can be configured for multi-site testing. Designs incorporate all necessary components, connectors, mechanical hardware and stiffeners to provide a complete plug-n-play solution. DTS has a vast database of tester and handler information which allow designs to be started and completed quickly without burdening the customer to supply excessive information. DTS designers are experienced in all device types, including digital, analog, mixed signal and RF devices.
-
MODEL DPM-2 -
Transducer Techniques, Inc
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
CA9809 -
UC Instruments, Corp.
The UC INSTRUEMNTS CA9809 2.0 ~ 68.0 Gb/s Pulse Pattern Generator pulse pattern generator and error detector is a high performance, flexible and costeffective broad band data rate covered Pulse Pattern Generator that can operate from 2.0 Gb/s to 68 Gb/s. The CA9809 can be used with existing equipment to generate higher rate bit streams for use in telecom applications up to 68 Gb/s. Broadband test systems will benefit from the low power dissipation, precision connectors, and excellent output waveform characteristics. The compact size of the equipment allows the CA9809 to be placed at the measurement plane, reducing or eliminating artifacts related to long cables.
-
SOA -
Amonics Ltd.
Amonics SOA is a polarization maintaining optical amplifier with high fiber-to-fiber gain. It is designed for transmitter applications to increase optical launch power to compensate for the loss of other optical devices. The benchtop version incorporates a user-friendly front panel housing a LCD monitor display, key switch, power control knob and optical connectors. RS232 computer interface is also equipped on the rear panel. 1MHz with 10ns pulse width intensity modulation is available. The OEM module version is an ideal building block for OEM system integration, especially in optical communication network and CATV applications. It requires only a single +5V power supply.
-
UBS2000 -
NG Systems Ltd
One of the main advantages of the Telematrix system is the relative ease in which both large and small matrix systems may be conceived and assembled from a selection of only five basic components. The five main components forming the Telematrix are the Enclosure, the CPU Card, the Input Card, the Output Card and the Input Device (keyboards etc.). Cards simply slide into the enclosure on nylon card guides and secured by two small screws. Keyboards are connected by a flexible 4 core telephone lead and plug into the Telematrix using standard BT plugs (X2110, X2120) or via a standard 4 pair CAT5 cable terminating on RJ45 IDC connectors (X2140).
-
Acces I/O Products, Inc.
A small form factor embedded computer board, typically intended for use in small, space-constrained industrial control or vehicles systems. The standard size of these modules is just 3.550 × 3.775 inches (90 × 96 mm). The name PC/104 comes from the original IBM computer known as the "PC", and the number of pins used to connect the cards together (104). PC/104 boards are typically stacked on top of each other using stackable bus connectors and four mounting holes at the corner of each module. This provides a much more rugged, embedded computer that can be used in harsh environments such as those found in military or industrial applications.
