Showing results: 871 - 885 of 2906 items found.
-
Virginia Panel Corporation
The D25 is capable of mating a wide variety of I/O module configurations, and can engage up to 5,952 signal contacts. All iDock Series connectors are compatible with VPC's existing line of modules, contacts, and tools.
-
East Coast DataCom, Inc.
The DBU-TTL Data Broadcast Unit is designed for use in receive only data broadcast applications. The unit supports 8-Ports Data/Clock distribution of TTL signals on BNC connectors. 1U rack mount chassis.
-
AC1000A -
Aim-TTi
Provides an EN61000–3–2 compliant source1000W power capability at 230VUp to 4·4A rms load current and up to 10A peak currentsComprehensive overload protectionConnection via standard power connectors
-
Apevia Corp.
Power supply is a standard-size Flex-ATX unit that will fit in any ITX form-factor case. Has enough power output and connectors to run low-medium systems being used for versatile compact computing applications.
-
J90RJ45R -
6TL Engineering
RJ45 Ethernet connector for VPC Tripaddle 90 series RCV module Up to three connectors per module For Cat 5 Fast Ethernet cable IEEE 802.3 standard 100 Base-T
-
AUTO DIAGNOSTECH LTD
The Sensor Imitator Probe is mainly used for the simulation of the signals generated by different types of sensors in the vehicle. It can be used in all automobiles (12V/24V), to distinguish faults that lie in the sensor itself or are related to the connectors or wires.
-
CONM50-D25-1 -
Abaco Systems Inc
An 18" ribbon cable transitions from individual IP Module ribbon connectors on the ISA (PC/AT) carrier board to a 25 pin female D-sub connector mounted on a PC expansion card end-panel.
-
CX-G13 -
Shenzhen Chuangxin Instruments Co., Ltd.
Tumbling Barrel Tester The Tumbling Barrel Test simulates repeated falls which may occur to such devices as connectors or small remote control units which are normally attached to cables during use.
-
FMC424 -
Abaco Systems Inc
Electrically compliant with the VITA 57.1 standard, the FMC424 is compatible with Abaco Systems' FPGA carrier cards offering high pin count connectors. It also allows for the option to stack an additional FMC over it.
-
N1420A -
Keysight Technologies
The N1420A is optional software to compare, evaluate and record noise from test setup. It is helpful when you isolate the cause of noise related to setup elements such as cables, connectors, shields, chambers, etc.
-
781131-03 -
NI
The TB-2650 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2650 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
Pickering Interfaces Ltd.
The Standard Voltage 9-Pin D-Type connector is used on PXI switching products to provide a low density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
Pickering Interfaces Ltd.
The Standard Voltage 50-Pin D-Type connector is used on PXI switching products to provide a medium density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
Virginia Panel Corporation
The D12 is capable of mating a wide variety of I/O module configurations, and can engage up to 2,880 signal contacts. All iDock Series connectors are compatible with VPC's existing line of modules, contacts, and tools.
-
106PIBM601-0000R -
ELMA Electronic, Inc.
The PIB 6U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.