Showing results: 886 - 900 of 2906 items found.
-
106PIBM301-0000R -
ELMA Electronic, Inc.
The PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
OPENVPX-CABLE -
ELMA Electronic, Inc.
Compliant to VITA 46 and 65, the cabling assemblies are ideal for development. They can be used for I/O to bulkhead connectors and slot-to-slot connections. Front-plug versions allow testing across the backplane or full interconnect path.
-
610102114 -
Virginia Panel Corporation
The 40 GHz Coax contact is a blind mate connector that mates with 3.5 mm and 2.92 mm connectors. It is recommended to use 2.92 mm connectors for frequencies above 35 GHz. The temperature range is -50°C to +125°C.
-
Comtel Electronics
Comtel Electronics offers the Serial Mesh Backplanes PICMG 2.20 High Speed mesh connections on ZD connectors (P4 area). Fully compliancy with PICMG 2.0 Rev 3.0 Specs & 2.20 Spec.
-
COMM-connect
The COMM-connect Low Noise Amplifier can be used to amplify signals in a wide range of bands. The amplifier comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
LPPHOT02 -
Delta OHM S.r.L.
Outdoor photometric probe for measuring ILLUMINANCE (0…150 Klux), CIE photopic filter, diffuser for cosine correction. mVdc output for klux. Complete with Calibration Report. On request 5 or 10m cables with connectors.
-
Macom Technology Solutions Holdings Inc.
MACOM offers 40G and 50G amplified PIN photoreceivers with high responsivity PIN photodiodes usable from 1200 – 1650 nm. These products are available in butterfly packages with single-mode fiber and coaxial output connectors.
-
40-965-009-M -
Pickering Interfaces Ltd.
Suitable for use on the front of modules this connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
40-965-009-F -
Pickering Interfaces Ltd.
Suitable for use on the front of modules this connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
778620-04 -
NI
37-Pin D-SUB Female to 37-Pin Bare Wire Female, 12 ft, Pigtail I/O, Shielded Multifunction Cable - The SH37F-P-4 connects compatible CompactRIO modules to accessories or cables with bare wire connectors.
-
85038A -
Keysight Technologies
The Keysight 85038A calibration kit contains open circuits, short circuits and terminations with both male and female 7-16 connectors and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
PAS-00023-25 -
Spanawave Corporation
* Solid State Power Amplifier* Gain : 46 dB typ.* High IP3, 48.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Over Temperature Protection* Type N Connectors
-
Virginia Panel Corporation
The D3/D4 connector is capable of mating a wide variety of I/O module configurations, and can engage up to 672 signal contacts. All iDock Series connectors are compatible with VPC's existing line of modules, contacts, and tools.
-
28V-SM-CARR-C -
ELMA Electronic, Inc.
The 28VDC carrier card with confirmal coating provides all the connectors necessary for the monitoring and control functions of any Elma systems, and also the power supply filtering required by the noise and transients consistent with MIL-STD-704E.
-
32290-204-0p60 -
ELMA Electronic, Inc.
9U VME64x Backplane 4-slot, VITA, termination passive inboard, daisy chain automatic active, 2x P47 power connectors, I/O pins 16mm gold-plated, shroud (1P1/nP2/nP0) optional latches