Showing results: 1051 - 1065 of 2906 items found.
-
Cabinet CP-101 & CP-102 -
Konrad Technologies GmbH
The CP-101 & CP102 are breakout panels which are used to provide a clear connection interface for 19” racks. They are equipped with the most common interfaces found on industrial computers. Both variants feature the same connectors, but distinguish in cable length (1m for CP-101 and 2m for CP-102).
-
E1739D -
Keysight Technologies
The E1739D 25-meter (82 feet) Sensor Cable is used to connect E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.
-
11878A -
Keysight Technologies
The Keysight 11878A adapter kit provides the RF components generally required when an SMA or 3.5 mm device needs to be measured with a network analyzer type-N configuration. This kit includes four type-N to 3.5 mm adapters for both male and female connectors.
-
049-566 -
ELMA Electronic, Inc.
CompactPCI Serial System Platform with 5 Slots: 4x CompactPCI-S.0 Peripheral Slots and 1x CompactPCI-S.0, System Slot on the right side of the system platform. High-speed connectors support data transfer rates of up to 12 Gbps for all slots.
-
SY7-CYCLONE -
ELMA Electronic, Inc.
SPE (Single Pair Ethernet) is a new emerging networking standard for many automotive and industrial applications. The EKF SY7-CYCLONE is a CPCI Serial FPGA board with front panel connectors for up to 20x100Mbps SPE ports. It can be configured as Ethernet NIC, switch, router, or gateway.
-
MSHD-02 -
Master Co. LTD
MSHD-02 distribute inputted component signal to the two (2) output channels via RCA connectors without diminuation & distortion. It takes High Bandwidth Video Distributor IC which is support the highest component resolution up to 1920X1080P & Dot Clock 148.5MHz.
-
PCIBPMC -
Dynamic Engineering
1/2 Length Bridge Based PCI Adapter Carrier Card with PMC Mounting Slot. The PCIBPMC ( PCI Bridge PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI slot. The PCIBPMC has a PMC card slot mounted to a universal 1/2 length PCI card. Suitable for 32 bit or 64 bit bus operation. The PMC user IO connector Pn4 is brought out to one of two connectors for access (DIN IDC or SCSI II). The signals corresponding to the PrPMC standard Ethernet and Serial lines can optionally be connected to the Ehternet and Serial port connectors at the top edge of the board.
-
MMA8452Q (Qwiic) -
SparkFun Electronics
This breakout board makes it easy to use the tiny MMA8452Q accelerometer communicate over I2C in your project. The MMA8452Q is a smart low-power, three-axis, capacitive MEMS accelerometer with 12 bits of resolution. This accelerometer is packed with embedded functions with flexible user programmable options, configurable to two interrupt pins. Embedded interrupt functions allow for overall power savings relieving the host processor from continuously polling data. This version of the SparkFun Triple Axis Accelerometer Breakout includes pre-soldered Qwiic connectors for rapid prototyping and better ease of use. With the connectors already soldered on, you can jump right into using this little board without any assembly!
-
MT-7068 -
Prokit's Industries Co., Ltd.
The MT-7068 All-in-one Toner & probe Kit lets you use Toner and Probe to validate and troubleshoot wiring on RJ11/RJ45 cables and connectors, USB, F, BNC, and RCA connectors, and it also supplied with alligator clips to work with. The MT-7068 Toner detects telephone and Ethernet service, indicates polarity and active line numbers on voice circuits, and indicates active pair number on Ethernet circuits. The MT-7068 Toner and Probe also provide standard functions such as visual and audible signal strength indication, analog toning/detection, and continuity testing. It is ideal for all maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling , etc.
-
U4206A -
Keysight Technologies
The U4206A is a direct-connect probe/cable with a standard soft touch pro connector at one end that routes to four 160-pin connectors that plug into the front panel connectors of a U4164A logic analyzer module. The U4206A is designed to be used with either the quad state mode or ¼ channel 10 GHz timing mode of the U4164A logic analyzer module. For use in quad state mode only, the U4206A includes two flying leads to connect additional clock qualifier signals into the clock inputs on Pods 3 and 7. Please refer to the U4164A installation guide for specific details on the operation of the U4164A quad sample state or ¼ channel 10 GHz timing modes of operation.
-
CB51 -
CAMI Research Inc. (CableEye®)
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models. The CB51, sold without connectors, contains four sets of 60 solder pads accommodating numerous configurations of surface mount and TH connectors aligned or staggered pins at 1.25mmm and 1.5mm pitch. There are four preset locations for automatic detection & display of any-pin-count connector up to 60-pins. Yet, any single set may be fitted with any combination of lower pin count connectors that total to 60 or less (e.g. a 40-pin with a 10-pin). Connectors soldered in non-preset positions will also appear graphically correct once they are mapped with PinMap (optional software).
-
FM510 -
Sundance Multiprocessor Technology Ltd.
The FM510, an air cooled Video I/O FMC, is used for standard-definition (SD) and high-definition (HD) video processing in combination with I/O and control applications. The front panel contains two HD-BNC connectors as primary video interface and a high0-density connector for secondary video and I/O interfaces.
-
Optical Wavelength Laboratories
7-segment LED wavelength displayMultimode and singlemode readyDual-wavelength ports allow automatic wavelength switchingTest two wavelengths at a timeSC connectors (ST and FC available upon request)Bundle with Fiber OWL 7 optical power meters for automatic dual-wavelength Tier 1 certification
-
Virginia Panel Corporation
The G2 offers the reliability of VPC interconnect technology in a compact, high-density two-module package. While simultaneously engaging a wide range of interconnect options in multiple configurations, the G2 provides a rapid alternative to repeated connect and disconnect of individual leads and connectors in a rugged, reliable system.
-
DX-101 -
Dexing Magnet Tech. Co., Ltd
DX-101 Gaussmeter is based on the Hall effect magnetic field strength of the latest developments in instrumentation, the design of desktop-type Gauss meter. Maximum range 330.0mT and 3000mT two tranches, the minimum basic error of 1.0%. Test probe connectors is imported, stable and reliable connection.