Showing results: 1216 - 1230 of 2906 items found.
-
80962-002-6600 -
ELMA Electronic, Inc.
6U CompactPCI Backplane 2-slot, PICMG 2.0 R3.0, system slot right, supports full hot swap function according to PICMG 2.1 R2.0 hot-swap specification, clock frequency 33MHz, V(I/O) +5V, bus width 64-bit, power input connection with Fastons connectors
-
80952-002-6600 -
ELMA Electronic, Inc.
6U CompactPCI Backplane 2-slot, PICMG 2.0 R3.0, system slot left, supports full hot swap function according to PICMG 2.1 R2.0 hot-swap specification, clock frequency 33MHz, V(I/O) +5V, bus width 64-bit, power input connection with Fastons connectors
-
80952-002-6610 -
ELMA Electronic, Inc.
6U CompactPCI Backplane 2-slot, PICMG 2.0 R3.0, system slot left, supports full hot swap function according to PICMG 2.1 R2.0 hot-swap specification, clock frequency 33MHz, V(I/O) +5V, bus width 32-bit, power input connection with Fastons connectors
-
80952-003-6600 -
ELMA Electronic, Inc.
6U CompactPCI Backplane 3-slot, PICMG 2.0 R3.0, system slot left, supports full hot swap function according to PICMG 2.1 R2.0 hot-swap specification, clock frequency 33MHz, V(I/O) +5V, bus width 64-bit, power input connection with Fastons connectors
-
80952-003-6610 -
ELMA Electronic, Inc.
6U CompactPCI Backplane 3-slot, PICMG 2.0 R3.0, system slot left, supports full hot swap function according to PICMG 2.1 R2.0 hot-swap specification, clock frequency 33MHz, V(I/O) +5V, bus width 32-bit, power input connection with Fastons connectors
-
SX5-STREAM -
ELMA Electronic, Inc.
The SX5-STREAM is a CompactPCI® Serial host adapter card for dual PCI Express® x8 external cabling. The board is provided with two PCIe® x8 front panel connectors, for attachment of one or two remote (target) systems via PCI Express® x8 links.
-
V976 -
CAEN S.p.A.
The Mod. V976 is a 1-unit VME module housing four 4-input Coincidence Fan in/Fan out and NIM – TTL / TTL – NIM adapter sections. Each section features 4 inputs and 4 outputs on LEMO 00 connectors and can operate as a 4 channel level translator or as AND/OR gate.
-
GX6196 -
Marvin Test Solutions, Inc.
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
CBT-500 -
Hosa Technology Inc.
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
60-760-005 -
Pickering Interfaces Ltd.
The 60-760-005 is a single 24x8 High Frequency Matrix Module suitable for switching frequencies up to 50MHz. It has an impedance of 50Ω and uses BNC signal connectors. It is also available in a smaller enclosure with SMB Connectors. It is designed to provide simple and scalable switching for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems.
-
E220-6U-1 -
VECTOR Electronics and Technology, Inc.
6U x 220mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides. Pad and bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
8018 -
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector.Pad-Per-Hole both sides.Combination Pattern: Half 2mm grid and other half 0.1” grid. Pad and bus surfaces solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
HW-05C -
Shanghai Fibretool Technology Co.,Ltd.
The HW-05C Fiber Optic Cleaver gives you high precision at low cost. This compact and easy to use cleaver is perfect for all cleaving applications, from fusion splicing to mechanical splicing and field installing quick termination connectors. The HW-05C works with both 250um coated and 900um buffered fibers.
-
Radiall s.a.
Radiall's extensive range of RF cable assemblies features outstanding electrical performance, low loss and high frequency. The range includes flexible, semi-rigid, corrugated and hand-formable cable assemblies with a combination of RF cables and connectors optimized for each market or application. Custom RF cable assemblies are also available.
-
Telewave Inc.
Prices include interconnect cables and mounting rails or panels. Specify N or UHF connectors, or 7-16 DIN (extra cost). All duplexers are factory turned. Specify pass and reject frequencies. 30-50 MHz duplexers have a tuning range of approximately +/- 2.5 MHz from center frequency as built.