Showing results: 301 - 315 of 858 items found.
-
MAGSYS Magnet Systeme GmbH
MAGSYS magnetizers allow the magnetization, adjustment and also the demagnetization of isotropic and anisotropic magnetic materials of different sizes. In particular, all highly coercive magnetic materials, such as Sm2Co17 or plastic-bonded NdFeB magnets, can be magnetized easily and with short cycle times. In addition to raw magnets, e.g. directly after production, complete workpieces with magnets already installed can also be magnetized.
-
MAG-ST100 -
R&J Measurement
The computerized measuring system is designed for measure the static magnetic properties of the hard magnetic materials e.g. Alnico, ferrite, magnets based on cobalt alloy with rare-earth elements or Nd-Fe-B alloy. The system provides the opportunity of a tabular and graphic presentation of the obtained data, which can be presented by means of monitor, printer or plotter. MAG-ST100 system fulfill the requirements of IEC404-5 Standard.
-
EM-6879 | 10 KHz – 30 MHz -
Electro-Metrics Corp.
The EM-6879 Loop Antenna is used for magnetic field measurements over the frequency range of 10 kHz to 30 MHz. The EM-6879 is designed for use with any 50 ohm Receiver System. The antenna has a balanced Faraday shield that reduces its response to electric fields to a vanishingly small amount so that it can produce a practically pure magnetic field response.
-
Schwarzbeck Mess Elektronik
Nearfield Probe Set includingHFSL 7101 Active Near Field Probe (magnetic), 9 kHz - 30 MHzHFSH 7102 Active Near Field Probe (magnetic), 4 MHz - 1000 MHzEFS 7103 Active Near Field Probe (electric), 9 kHz - 1000 MHzand Separator EW 7110 and AC/DC adaptor ACDC 7110 in storing case
-
Magna-Mike 8600 -
Evident Scientific
The Magna-Mike® 8600 is a portable thickness gauge that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
Motion Control Systems, Inc.
Using MCS''s proprietary magnetic circuits and high-energy magnets, our engineers have created a motor line that combines high power density with smooth, highly reliable performance Exceptional efficiency can be achieved to minimize heating and maximize continuous power rating.By varying the lengths of the lamination and magnetic circuits, a single frame size can handle a wide range of applications.
-
425 -
Cooper-Atkins Corporation
Gun-Style Infrared thermometer with Dual Laser Sighting, LED Flashlight and Hi/Lo Alarm. With HDPE carrying case and magnetic stand.
-
TDK RF Solutions Inc.
TDK E-Field Generators - generate controlled, high-intensity electric and magnetic fields over the frequency range of 10kHz to 100 MHz
-
Denshijiki Industry Co., Ltd.
And the eddy current generated on the specimen by the specimen by the action of the magnetic field can not be detected (defect) and the change due to the influence of the material is detected.
-
MultiDimension Technology Co.,Ltd.
A three-axis digital magnetometer that is intended for the measurement of magnetic fields near the probe tip at frequencies less than 250 Hz.
-
SICK Sensor Intelligence
Reliable, high-performance, rugged - magnetic cylinder sensors from SICK for the T-slotMagnetic cylinder sensors from SICK ofter the perfect option for all conventional pneumatic actuators with T-slots. They are precisely tailored for the different nut tolerances. Thanks to the huge range of magnetic cylinder sensors to choose from, we can meet your every need. Drop-in mounting, short, compact design with enormous retaining force, combination bolt, safe switching point detection, sensors with two switching points, and universal mounting options using an adapter make it clear: Magnetic cylinder sensors from SICK are prepared for all installation sites and situations.
-
421 -
Oersted Technology
The Model 421 is a benchtop, laboratory gaussmeter, capable of measuring magnetic fields from 0.001 Gauss to 300 kGauss (measurement range is dependent on probe used). This unit is well-suited to magnet testing, quality assurance, and other applications requiring highly repeatable magnetic measurements. Measurements of AC and DC magnetic fields are shown in Gauss or Tesla on the two-line vacuum fluorescent display. A Sort function allows magnet parts to be quickly checked on a pass/fail basis, while the serial port enables the gaussmeter to be controlled by a computer or automation equipment. A hall-effect gaussmeter probe is included with the Model 421, and may be selected from an extensive line of probe constructions.
-
Shimadzu Corp.
The analysis of dioxins in foods was mainly performed using magnetic sector (double-focusing) GC-MS instruments. However, in June 2014, the GC-MS/MS method was officially recognized in the EU as being equivalent to the magnetic sector GC-MS method (EU 589/2014). This product consists of method files for the analysis of dioxins in foods, and a report creation tool, supporting the analysis of dioxins via GC-MS/MS.
-
4029 -
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
IDR-210 -
Integrity Design and Reseach Corp.
Typical Applications include checking the frequencies and magnetic fields (BW: 20-4000 Hz) produced by equipments such as computer monitors, television sets, power lines, induction heaters, industrial, scientific and medical equipment and household appliances, etc. Magnetic fields are invisible radiations, the best method to detect them is by using one of the accurate gaussmeter from Integrity Design & Research Corp.