Showing results: 2941 - 2953 of 2953 items found.
-
ERAVANT
Dual polarized horn antennas are offered as both standard and custom models with rectangular waveguide interfaces for both horizontal and vertical ports. These dual polarized horn antennas support both linear and elliptical polarized waveforms. When the antenna receives a circular polarized waveform, equal amplitude linear polarized waveforms are output at both horizontal and vertical ports. When two equal amplitude linear polarized waveforms are input into the vertical and horizontal ports, the antenna will transmit a circular polarized waveform. The listed models offer 15 dB nominal gain and 33/28 degrees typical half power beamwidth at the center frequency of the band. They also exhibit 40 dB typical port isolation and 35 dB nominal cross polarization. These antennas cover full waveguide bandwidths within the frequency range of 8.2 to 110 GHz. In addition to the models listed below, models with 10, 20, 23 and 25 dB gain and other frequency bands are also available.
-
CM22303 -
LinkedHope Intelligent Technologies Co.,Ltd.
CM22303 uses Intel® 7th generation Kaby Lake-Y platform and Core M Ultra low-power SoC processors, and integrates the full functions of CPU, GPU and South/North Bridge on a single chip. The processor provides powerful computing and display performance with dual-core and four threads configuration. Its turbo frequency can boost up to 3.6 GHz and the display output resolution can be up to 4K. CM22303 has an amazing thermal design power consumption of only 4.5W (TDP) and can be used for a variety of high-performance fanless designs. SPI BIOS is designed on board to support dual-channel low voltage on board memory (up to 16GB), Gigabit Ethernet, TPM module and other functions. With high-performance and low power consumption, it can be widely used in the field of low power embedded systems. Meanwhile, CM22303 adopts COM Express standard and is compatible with Type10 pin out definition, and also provides rich peripheral interfaces such as USB3.0/2.0, PCIe, SATA, HD Audio etc.
-
ICO300 -
Axiomtek Co., Ltd.
With din-rail, fanless and rugged design, the ICO300 embedded system utilizes low power 22nm Intel® Atom™ processor E3815 (1.46 GHz) and supports DDR3L system memory maximum up to 4GB, delivering high performance at competitive price. This intelligent Intel® Atom-based IoT gateway solution supports complete expandability and features, including wireless support, four RS-232/422/485 ports, two isolated Gigabit Ethernet ports, two high-speed USB 2.0 ports, RTC battery function, and wide range 12-24VDC power input with terminal block. The ICO300 is also Axiomtek's first IoT gateway solution certified by Microsoft Azure IoT. The application-ready ICO300 simplifies the development process and achieves accelerated business transformation of IoT environment. This intelligent IoT gateway system provides a perfect solution for IoT & M2M, industrial and embedded applications such as power plant automation, facility monitoring systems, intelligent transportation systems and other harsh environments.
-
LDA-602EH -
Vaunix Technology Corporation
The LDA-602EH has a large attenuation range of 120 dB with an exceptional 0.1 dB step size, allowing for both precision and accuracy during fading tests or device characterizations. This attenuator also features a fast 15 us switching speed, an operating temperature from -30oC to 50oC, a maximum RF input of +28 dBm, and is priced at $875. The LDA602-EH operates with a low insertion loss of 9 dB to 6 GHz, an input IP3 of +55 dBm and a typical VSWR of 1.3:1. Easily programmed for ATE applications, the LDA digital attenuators are a cost effective solution whether you are in engineering, the production test lab, or in the field. Units are ROHS compliant and can be used with any PC or laptop computer with USB 2.0 port (or powered USB hub) and Windows operating system. Lab Brick Signal Generators are provided with easy to use Lab Brick GUI software, 32 and 64 bit API DLL files, LabVIEW and Linux compatible drivers.
-
CP67001 -
LinkedHope Intelligent Technologies Co.,Ltd.
CP67001 is a CompactPCI® processor board based on China local-manufactured Phytium FT1500A/4 4 cores ARM processor, with more than 10-year lifecycle. Designed with ARM v8 Architecture, 28nm process technology and fine-grained power optimization technologies, its CPU integrates 4 ARM cores with CPU clock speed up to 2.0 GHz. Combined with the maximum power consumption of 15w, CP67001 is highly applicable for making low-power-consumption solutions.Equipped with Intel82580, CP67001 supports 4x Gigabit Ethernet; 4x SATA 2.0 and 8x USB 2.0; 1x16 PCI Express for XMC and PMC; SM750 graphic controller with resolution up to 1920x1080p. CP67001, as a single board computer has up to 64GB flash memory, provides outputs including HDMI, DP, DVI and VGA, and provides 2 serial ports with one port supports RS232/RS422/ RS485 configurable through software. In addition, CP67001 supports GPIO and can meet customized demands in different situations.
-
F-Series -
Emite Ingeniería SL. Ed
The F large-size hybrid Reverberation/Anechoic Chamber represents the most versatile OTA test system in the market today. With the same unique test features of their E Series RC counterparts, the F-Series can also test large form-factor devices under test (DUTs) like laptops, large TV sets, solar and trash compactors, drones, fridges or washing and vending machines, among others. With up to 16x16, 8DLCC and DUTs up to 2m and 500 kg including full-body phantoms in a turntable, the F Series also expands the frequency range down to cover 200 MHz up to 40 GHz frequency ranges and the test modes to include EMC, BS, small cell, eNodeB and Virtual Drive Testing over the air (VDT-OTA). In an again unheard-of feature, the F-Series is also reverse-convertible into an Anechoic chamber, allowing Far Field (FF) and Spherical Near Field (SNF) radiation patterns, efficiency and gain measurements and pre-5G testing of antennas and devices. Conversion from RC to AC or vice versa can be performed within half a day.
-
BAW -
Macom Technology Solutions Holdings Inc.
MACOM’s BAW product portfolio is ideal for high performance Industrial, Aerospace, Defense, and Communications applications that require critical frequency filtering. Our high-performance RF filters enable our customers manage signal integrity in the 1 to 6 GHz frequency range. Bulk Acoustic Wave Resonators consist of two metal electrodes above and below a layer of a piezoelectric material. The piezoelectric material converts an electrical signal to a mechanical signal and vice versa. The metal electrodes provide the connections to/from the piezo material. The frequency at which resonance occurs depends on the thickness of the combined metal-piezo-metal stack. Advances in thin-film piezoelectric fabrication have enabled BAW resonators to meet RF filtering challenges up to 6000 MHz using standard MEMS fabrication process. High-performance BAW resonators-based RF filters are made of piezoelectric material having high Q-factor (>3000) and high coupling coefficient. Currently, no competitive technology provides the same high performance for RF filter applications when compared to BAW resonator-based RF filter up to 6000 MHz for the same size and cost.
-
Optoplex Corporation
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5,10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systemsutilized in commercial, defense and space exploration markets. The device plays a key role in improvingsignal quality and performance to meet the expanding demand for higher data rates and more complextransmission formats within current and next generation systems without major capital expenditure.Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. The measured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarization-dependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
Optoplex Corporation
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5, 10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systems utilized in commercial, defense and space exploration markets. The device plays a key role in improving signal quality and performance to meet the expanding demand for higher data rates and more complex transmission formats within current and next generation systems without major capital expenditure. Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. Themeasured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarizationdependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
Maury Microwave Corporation
Maury manual tuners are based on precision slide screw technology that utilizes broadband slab line transmission structure and passive probes to create impedances for devices. The probes are designed to be very close to onequarter wavelength in the linear dimension at the mid-band of each range. Since each tuner has two probes, this results in improved matching characteristics for each unit. Another key feature of this series of tuners is the inclusion of a LCD position readout of the carriage position on those units operating below 18 GHz. Higher frequency tuners utilize a micrometer carriage drive. The positional repeatability and high matching range of these tuners make them ideally suited for use as a variable impedance source in applications like device characterization. Such measurements depend upon the ability of the tuner to establish impedances out near the edge of the Smith chart and to reproduce the electrical characteristics as a function of mechanical position. The tuners in this series are also easy to use due to the nearly independent electrical results of the mechanical motions. The depth of penetration of the probe into the transmission line determines the magnitude of the reflection, while the position of the probe along the line determines the phase. While there is some interaction, the effects are almost independent of each other. https://www.maurymw.com/images/mw-rf/mst982e35.jpg
-
Pasternack Enterprises, Inc.
Our RF termination loads (also know as terminators) are available in 1.85mm, 2.4mm, 2.92mm, 4.1/9.5, 4.3-10, 7/16 DIN, BMA, BNC, Type C, Mini SMP, MMCX, Type N, QMA, SMA, SMB, SMC, SMP, SSMC and TNC connector types. RF termination loads from Pasternack are organized into two categories, feed-thru terminations and RF terminations. Pasternack Enterprises RF load terminations include precision and standard versions and many are RoHS and REACH compliant. 0.25 Watts, 0.5 Watts, 1 Watts, 2 Watts, 5 Watts, 10 Watts, 25 Watts, 50 Watts and 100 Watts models. Pasternack RF terminations are offered with impedances of 50 Ohm, 75 Ohm or 93 Ohm. The frequency ratings for these RF coaxial load termination range from DC to 50 GHz. RF loads are available in female, jack, male, male to female and plug genders. Our RF termination loads varieties are RoHS and REACH compliant. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this RF terminator series is in-stock. Not just in stock, but also these RF terminations will ship the same day as they are purchased from Pasternack.
-
Pasternack Enterprises, Inc.
Pasternack unequal split power tapper product designs are also known as unequal couplers, power dividers or splitters, cross band couplers and signal samplers. Many of our unequal couplers / tapper series are RoHS and REACH compliant. Unequal RF tappers from Pasternack are available with 4.1/9.5, 4.3-10, 7/16 DIN and Type N connector options. These unequal split power tapper components for RF are manufactured to precise specifications required for accurate specified values listed for each product. Unequal split tapper products work with high power of up to 300 watts depending on style. Frequency ratings for unequal power splitter line are wide band components with a 380 MHz to 6 GHz frequency range, based on model selected. Pasternack RF power tappers in unequal design can be ordered with various directivity (dB) values of 4.8dB, 5dB, 6dB, 7dB, 8dB, 9dB, 10dB, 11dB, 12dB, 13dB, 15dB, 16dB, 20dB, 30dB depending on model. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this unequal split power tapper/coupler/divider series for RF is in-stock. These unequal split power tappers are not just in stock, but they will also ship the same-day are they are purchased.
-
MIC-3398 -
Advantech Co. Ltd.
The MIC-3398 is a Low-Power 6U CompactPCI® CPU blade with best in class price/performance ratio tailored for applications that require a state of the art processor platform based on Intel® Architecture with full IO capability at an attractive cost point. The MIC-3398 supports Intel® Atom™ E3845 and Celeron N2930, J1900 SoC (system on a chip) family previously codenamed Bay trail with a maximum of quad-core 2.00 GHz processing performance. Intel® Atom™ technology provides significant increases in performance and energy efficiency by using the 22nm Intel® manufacturing process making it an ideal choice for control and workstation applications that require passive cooling with a power dissipation as low as 10W. Up to 8GB, dual channel 1333 MHz DDR3L memory with ECC support provide a high performance and robust memory interface for demanding applications. With built-in graphics based on Intel® HD Graphics Technology this blade offers a significant improvement in graphics performance compared to previous generation platforms. Support for an onboard 2.5” SATA-II drive as well as CFast SSDs adds comprehensive mass storage support. On the system side, the MIC-3398 supports 32-bit, 33MHz and 64-bit, 66MHz PCI bus interfaces to a CompactPCI backplane. A rich set of I/O interfaces such as DVI-D, USB3.0/2.0, Gigabit Ethernet and RS-232/422/485 ports round off the feature set. In addition to the single slot wide (4HP) board offering, a dual slot wide (8HP) version of the blade offers additional network connectivity by increasing Gigabit Ethernet port count from two to four.
