Showing results: 931 - 945 of 2953 items found.
-
N4691D -
Keysight Technologies
The Keysight N4691D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4691D is a precision 2-port ECal module that supports 3.5 mm connectors up to 26.5 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4691D is included for securing your ECal module and accessories.
-
P9404A -
Keysight Technologies
The Keysight P9404A PIN solid state switch maximizes your operating frequency range from 100 MHz to 8 GHz. Providing superior performance in terms of isolation, insertion loss and return loss, the P9404A is particularly suitable for high-speed RF and microwave switching applications such as switch matrixes in instrumentation, communications and radar. These switches provide ultra-fast switching speed to increase throughput in manufacturing.
-
P9402C -
Keysight Technologies
The Keysight P9402C PIN solid state switch maximizes your operating frequency range from 100 MHz to 18 GHz. Providing superior performance in terms of isolation, insertion loss and return loss, the P9402C is particularly suitable for high-speed RF and microwave switching applications such as switch matrixes in instrumentation, communications and radar. These switches provide ultra-fast switching speed to increase throughput in manufacturing.
-
P9404C -
Keysight Technologies
The Keysight P9404C PIN solid state switch maximizes your operating frequency range from 100 MHz to 18 GHz. Providing superior performance in terms of isolation, insertion loss and return loss, the P9404C is particularly suitable for high-speed RF and microwave switching applications such as switch matrixes in instrumentation, communications and radar. These switches provide ultra-fast switching speed to increase throughput in manufacturing.
-
P9402A -
Keysight Technologies
The Keysight P9402A PIN solid state switch maximizes your operating frequency range from 100 MHz to 8 GHz. Providing superior performance in terms of isolation, insertion loss and return loss, the P9402A is particularly suitable for high-speed RF and microwave switching applications such as switch matrixes in instrumentation, communications and radar. These switches provide ultra-fast switching speed to increase throughput in manufacturing.
-
11923A -
Keysight Technologies
The Keysight 11923A 1.0 mm female connector launch is designed to thread into a package or fixture housing to transition a microwave circuit from microstrip to coaxial connector. The Keysight 11923A connector launch is intended for use with 110 GHz test systems such as the Keysight 8510XF. The Keysight 11923A comes pre-assembled, but the user is responsible for machining the package and installing the connector. The procedure describing the necessary geometry for the package and installation will be provided.
-
Insight Product Company
*Frequency band, GHz: 33-37 *Output power, typical, W: 10 (40 dBm) *Gain, dB, typical: 30*Gain flatness: 2 dB Max *Pulse width, Max.: 100 nanoseconds - 60 microseconds *Pulse reptition frequency: up to 100 KHz *Oprating temparture: -40 deg. Celsius to 60 deg. Celsius *Dimensions: 245 mm x 124 mm x 30 mm
-
M9157C -
Keysight Technologies
M9157C operates from DC to 26.5 GHz, providing a low-cost operation switching solution for measurement and automation of Automatic Test Equipment (ATE) systems without compromise in the RF performance. It is being used in applications such as ATE, RF communication and RF parametric measurements where a rugged switching module is needed for signal routing. Typical switching applications for multiport coaxial switches include signal routing to a single input to multiple instruments and routing of multiple input signals.
-
Talon RTR 2613 -
Pentek, Inc.
The Talon® RTR 2613 combines Pentek’s Sentinel Intelligent Signal Scanning software with real-time recording in a lightweight, portable and rugged package. The RTR 2613 provides SIGINT engineers the ability to scan the 3 GHz spectrum for signals of interest and monitor or record bandwidths up to 40 MHz wide once a signal band of interest is detected. The RTR 2613 recorder is a grab-and-go recorder suitable for test & measurement, mobile military, security and government intelligence (SIGINT, COMINT and ELINT) applications.
-
ZS2500 -
Teledyne LeCroy
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS2500 is ideal for 2.5 GHz and lower oscilloscopes.
-
CT4121 -
Cal Test Electronics
The CT4121 is a compact FET probe with very high input resistance and low input capacitance. With a 1.2 GHz bandwidth, this probe is ideal for timing analysis or troubleshooting high speed logic circuits, for design verification of disk drives, as well as for wireless and data communication design. The CT4121 can measure up to ±40 V (DC + AC peak). Compatible with oscilloscopes from all major manufacturers, the probe is powered by the included 9 V battery or direct from the oscilloscope using the included USB power lead.
-
782512-01 -
NI
The NI‑5793 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5793 modules.
-
782511-01 -
NI
The NI‑5792 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5792 modules.
-
782510-01 -
NI
The NI‑5791 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5791 modules. For higher frequencies or a greater number of devices, you can use an external LO distribution amplifier.
-
785672-01 -
NI
2.1 GHz, 1U Rugged Rack-Mount External Controller for PXI—The RMC‑8357 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon eight‐core processors that support up to 32 GB of RAM. The RMC‑8357 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8357 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.