Showing results: 226 - 240 of 768 items found.
-
DAQ-2213/2214 -
ADLINK Technology Inc.
*16-bit A/D and sampling rate up to 250kS/s*16-CH single-ended or 8-CH differential inputs*512-configuration channel-gain queue*Analog and digital trigger
-
ATS9353 -
AlazarTech
ATS9353 is a low-noise 12-bit waveform digitizer board designed for OEM customers. It can sample two analog inputs at rates up to 500 MS/s.
-
TPMC532 -
TEWS Technologies GmbH
The TPMC532 provides 16 or 8 channels of simultaneous sampling true differential bipolar 16-bit analog input, 8 or 4 channels of simultaneous update single-ended unipolar/bipolar 16-bit analog output and 14 channels of tri-state 5V-tolerant TTL digital input/output.
-
0001045 -
VI Control Systems Ltd.
Interface board plugs directly into National Instruments 68 pin multifunction and simultaneous sampling DAQ cards (PCI and PXI). First four analog inputs, two analog outputs, and trigger channels are available on BNC connectors (SMA/SMB optional).
-
Scientific Columbus -
Ametek Power Instruments
Scientific Columbus brand Analog Transducers can cover any power application with the wide variety of products. Select from any circuit type, input and power range, frequency, analog output and accuracy range and you will have an exact fit for any application.
-
Analog Devices Inc.
Analog Devices JFET input op amps or FastFET high speed (>50 MHz) input op amps provide high input impedance and ultralow input bias currents for high speed applications. The majority of our FET input op amps feature wide supply ranges from +5 V to 12 V or higher and feature rail-to-rail outputs enabling wide dynamic range.
-
DP-VME-2115 -
Data Patterns Pvt. Ltd.
DP-VME-2115 is an industrial standard 24 channel D/A (Digital to Analog) board. It incorporates most of the features which are demanded in industrial applications. Each Digital to Analog Converter (DAC) is provided with a separate reference voltage selection either from internally generated reference or from the external input. This external input reference signal is passed into the protection circuits before it is fed to any active components. The input protection circuit is designed for ± 25Vp-p input ranges. The DAC output may be unipolar or bipolar and the output is jumper selectable, which is routed to the VME P2 connector, with short circuit protection of upto 30mA.
-
780875-01 -
NI
Non-Enclosed, ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the sbRIO‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range. Non-enclosed modules are designed for OEM applications.
-
RATCAT Family -
Sound Tools
The CAT Snake Stage Box allows four lines of balanced analog audio to be run down a shielded CAT5/6/7 cable. Each of its four channels can carry balanced analog, AES/EBU, DMX, and Clear-Com signals hundreds of feet away. The CAT Snake is a fully passive unit which can be input directly into analog or digital consoles. Each channel is isolated which means channel 1 can send a DMX Signal while channel 2 is sending balanced analog all down the same shielded CAT5 cable. Multiple CAT Snake stage boxes can be daisy chained to allow the same four analog channels to be dropped in multiple locations. Each CAT Snake stage box has an Ethercon input and Ethercon parallel output that allows the CAT Snake to be used as a hard-wire split.
-
2608 Series -
Sensoray Co., Inc
16 inputs of voltage, thermocouple, or 4-20 mA16-bit A/D, 15 -bit D/AUp to 8 analog outputs with remote sensingAuto standardizationSelectable input gainAll differential inputsWatchdog TimerCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
VME-6500 6U -
Abaco Systems Inc
The VME-6500 is a 6U VME Multifunction I/O board that can deliver in a single chassis slot the analog and digital I/O capabilities that could previously have occupied four slots, and can therefore make a significant contribution to substantially enhance performance and functional density. A high density and versatile design it provides 8 analog inputs and outputs as well as 16 digital inputs and outputs, all in a single 6U double Euro form factor.
-
DACNF04 – HPC -
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF04 is a four channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit input and one DC coupled single-end analog output with DC – 250KHz sampling speed based on Linear Technology’s LTC2704-16. The 16-bit input data for each channel is provided through SPI from the FPGA on the FMC carrier board. A single-ended TTL level trigger output is provided from the FPGA.
-
ADwin-Gold II -
ADwin
10 times more computing power than ADwin-Gold with the processor ADSP TS101S at 300 MHzMore memory: 768 kB CPU-internal RAM, 256 MB DRAMHigher resolution: 2 18 bit ADC with 8 analog inputs each via multiplexerFIFO memory at the digital inputs for fast detection of rising and falling edges with 100 MHz event counter2 analog outputs, 16 bit, 32 digital I/Os (TTL)
-
ADC-MOD2 -
Curtiss-Wright Defense Solutions
Simple analog input to a processor is no longer enough. Software Defined Radio (SDR), RADAR, and telecommunications applications demand closely coupled high performance processing.
-
Ivium Technologies B.V.
The Peripheral Level Transformer (PLT) is an adapter module that increases the voltage of the analog inputs&outputs for easy communication with external devices. It is connected between the instrument and the periphery.