Showing results: 1306 - 1320 of 1778 items found.
-
Kuhne electronic GmbH
he products from Kuhne electronic from the category "Receiving Amplifiers for Professional Use" are designed for the following applications: Radio Link Systems, Satellite Receivers as well as Scientific and Measurement Instrumentation.These amplifiers stand out due to outstanding Noise Figures as well as a very good Large Signal Stability and small Housing Sizes.
-
RefRad X -
Seibersdorf Labor GmbH
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
SureTrace™ 955 -
IDEAL Industries, Inc.
Receiver display rotates automatically for easy viewingIdentifies breakers and fuses with CertainCircuit™ detection*Pinpoints open and shorts*Traces wires*0-99 display of signal strength*Audible indication intensifies in tone/pitch with signal strength*Works on energized or de-energized circuits (0-600V AC/DC)*Four sensitivity levels*Peak reading bar graph*2-year warranty
-
Nexeon HD Xtra -
dPict Imaging, Inc.
Nexeon HD Xtra is a full-featured video frame grabber for high-definition video display and capture. It supports viewing and capture from high-definition video inputs from SDI, HDTV and VGA display sources. Nexeon HD Xtras has a flexible input interface complete with an HDMI compatible receiver and supports both analog and digital DVI/HDMI standards.
-
PSI -
Computer Conversions Corporation
Computer Conversions Solid State Selsyn/Resolver Indicator digitizes the outputs of Selsyns, Synchros and Resolvers for position indication and control applications. The Selsyn Indicator is designed to replace failure prone mechanical selsyn torque receivers, counters, etc. The tracking converters high noise immunity and high speed tracking characteristics make it ideal for use in industrial envrionments.
-
Schwarzbeck Mess Elektronik
In addition to EMI measurement with LISNs (Line Impedance Stabilisation Networks, Artificial Mains Networks), Probes are used for Terminal or Line voltage measurement.LISNs are required to feed the Equipment under Test (EuT) with mains power, to reduce external line interference, to offer the EuT a standardized impedance and to route the extracted r.-f. voltage to the EMI receiver.
-
T24-WSS -
Mantracourt Electronics Ltd
The wireless wind speed transmitter (Anemometer) T24-WSS is built on Mantracourt’s T24 2.4 GHz wireless technology and operates alongside any T24 device such as base stations, handheld displays, analogue output, relay modules, GPRS data loggers, computer interfaces and more. Data transmitted by the T24-WSS can be received by multiple T24 receivers and displays.
-
SimMNSA -
Spirent Federal Systems
The M-code signal is part of the security architecture that all new Military GPS User Equipment (MGUE) has been required to use since 2017. Until recently, testing with non-classified AES-encryption and replay of M-code Satellite Data Sets (SDS) have been the only methods authorized for GPS M-code receiver testing using a constellation simulator.
-
SeaBat 7160 -
Teledyne Marine RESON B.V.
The SeaBat 7160 transducer array is comprised of linear receive and transmit arrays mounted together on a support base. The T-shaped array geometry provides the basis for a compact, high-resolution sonar which is easily installed for portable or hull mounts – a first for a high-resolution system in this frequency range. The system features a pitch-stabilized transmitter and an active roll compensated receiver.
-
LOUDSOFT
From 1993 Peter Larsen has worked as an independent consultant for leading loudspeaker factories all over the world. During his career the Ringradiator, a new Racetrack woofer and a 15mm Mobile receiver have been developed among several hundred other transducers. Complete High End enclosure systems and Monitors are among the latest additions.
-
EM-6876 | 9 KHz – 30 MHz -
Electro-Metrics Corp.
The Electro-Metrics EM-6876 Active Loop Antenna is used with EMI Receivers and Spectrum Analyzers with 50 ohm input and covers the frequency range of 9 kHz to 30 MHz.
-
610113173 -
Virginia Panel Corporation
* This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113172. (May mate with other Receiver contacts, as well.)
-
Data Patterns Pvt. Ltd.
The Generic RF ATE is developed to test the Radar and Radar Subsystems. The ATE is primarily built using an instrumentation control, precision RF routing systems and rack mounted test instruments. Generic RF ATE system enables measurement of parameters of Radar equipment such as Local Oscillators, Waveform Generators, Up and Down Converters, Analog Receivers, Array Group Receiver Units, TR Modules. The ATE is configured to test the Radars upto 18GHz frequency range.
-
ZOE-M8Q (Qwiic) -
SparkFun Electronics
The SparkFun ZOE-M8Q GPS Breakout is a high accuracy, miniaturized, GPS board that is perfect for applications that don't possess a lot of space. The on-board ZOE-M8Q is a 72-channel GNSS receiver, meaning it can receive signals from the GPS, GLONASS, BeiDou, and Galileo constellations. This increases precision and decreases lock time and thanks to the onboard rechargable battery you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
ST-C6DVI-300 -
Network Technologies Inc
The XTENDEX® DVI Extender transmits digital DVI video up to 300 feet away from a DVI source over a single CAT5/6/7 cable. Each video extender consists of a local unit that connects to a single link digital DVI source and optional IR emitter, and a remote unit that connects to a DVI display and optional IR receiver.