Filter Results By:
Products
Applications
Manufacturers
- Taylor Dynamometer, Inc.
product
Eddy Current Engine Dynamometers
A precise, low-maintenance, rapid response and repeatable alternative to water brake technology, Taylor’s Eddy Current Engine Dynos provide low-inertia, air- or water-cooled operation for testing engines up to 966 hp (720 kW) in a range of markets.
-
product
CAT-5 Cable Equalizers
Analog Devices high speed, differential receivers and CAT-5 cable equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Our design techniques for products such as the AD8123 optimize performance for low noise, short-to-medium range applications, while also providing the high gain bandwidth required for long cable equalizations. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths.
-
product
CellTest Multichannel Potentiostat
Simultaneous Electrochemical Impedance Spectroscopy (EIS) tests can be run on multiple cells by connecting Solartron 1455A/1451A series frequency response analyzer (FRA) modules to the 1470E. These FRAs can operate in single sine correlation or multi-sine / Fast Fourier Transform (FFT) analysis mode, providing the ultimate in speed, precision and accuracy. The 1455A FRA provides high performance impedance measurements over the frequency range 10 μHz to 1 MHz, while the 1451A FRA operates from 10 μHz to 100 kHz.
-
product
Clamp Meter, True RMS, 100 A AC, 600 V AC, 600 V DC, 17 mm Jaw Opening Max.
72-2985
The 72-2985 from Tenma is a mini clamp meter in orange and grey colour. It features high reliability, safety precision and compact design. Its resolution ratio is 1mA, maximum range has maximum range of 100A AC/DC, particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is true valid value. Whole range overload protection, reliable measurement accuracy and unique appearance design makes it an outstanding new generation functional electrician/electric power measurement instrument. This complies with EN 610101-1, 61010-2-032, 61010-2-033, pollution degree 2, measurement category: (CAT II 600V, CAT III 300V) and double insulation standards. Conforms to UL STD. 61010-1, 61010-2-032, 61010-2-33 certified to CSA STD. C22.2 NO. 61010-1, IEC STD 61010-2-032, 61010-2-033.
-
product
Combined Illumincance and Irradiance Probe
LP471P-A
Combined probe for measuring ILLUMINANCE (lux), with standard photopic response, and IRRADIANCE (μW/cm²) in the UVA spectral range (315…400 nm, with peak at 360 nm).
-
product
Combustible Monitor
SMC 5100-02-IT
The SMC 5100-02-IT gas sensor monitors combustible gases such as Methane, Hydrogen, Propane, and others. It is based on catalytic bead technology, a consistent and reliable method of detection that offers excellent response times to the target gases. The 5100-02-IT sensor offers multiple communication outputs including 4-20 mA and Modbus RTU.
-
product
Compact Infrared Thermometer With Laser Targeting
PIRT25
Unique Flat SurfaceMini-Modern Housing DesignSimple One-Handed OperationLaser TargetingLCD With BacklightCelsius or Fahrenheit ModesLaser On/Off SwitchAutomatic Power OffDisplay Hold FunctionMax/Min FunctionTemperature Range: -50 to 380 Celsius, -58 to 716 FahrenheitTemperature Resolution: 0.1Emissivity: Fixed at 0.95Optical Resolution: 8:1 Distance to Spot Size RatioBasic Accuracy: +2% of Reading or +2 C / +4 FResponse Time: <1 Sec.Diode Laser: Output <1mW @ 630-630nm, Class 11 LaserSpectral Response: 6-14umPower Supply: 9V BatteryDimensions: 7.09' H x 3.94' W x 1.81' DWeight: 5.6 oz.
-
product
Compact Loudspeakers
ULTRA-X40
The ULTRA-X40 brings the technology breakthroughs in our flagship LEO Family line arrays to a versatile, compact loudspeaker. Its innovative concentric-driver configuration couples two 8-inch cone drivers to a rotatable waveguide surrounding a 3-inch high-frequency compression driver, to deliver smooth response across its entire range and directional control down to 400 Hz.
-
product
Compact Low-Frequency Control Element
900-LFC
The 900-LFC Low-Frequency Control Element extends the response of mid-sized P.A. systems to 35 Hz, revealing the nuances of your mix, down to the deepest bass with total accuracy.
-
product
Comparators
Renesas offers a comparator portfolio that includes nano power comparators, high-speed CMOS comparators, and precision quad comparators. Our general-purpose comparators utilize CMOS processes suitable for low voltage, low power consumption, and fast response. We have also recently expanded our comparator offerings with Intersil comparator products.
-
product
Comparators
General-purpose comparators utilizing CMOS process suitable for low voltage, low power consumption, and fast response.
-
product
Comparators for Space & Harsh Environment
Renesas' MIL-STD-883-compliant monolithic, quad, precision comparator is qualified to QML Class Q military standards and offers fast response time, low offset voltage, low offset current and virtually no channel-to-channel crosstalk for applications requiring accurate, high-speed, signal level detection.
-
product
CompuScope GPU CUDA Processing
Performing real-time digital signal processing (DSP) routines such as Fast Fourier Transform (FFT), Signal Averaging, Finite Impulse Response (FIR) Filtering, Digital Down Conversion (DDC) and more have traditionally required the use of dedicated DSP processors, Field Programmable Gate Arrays (FPGAs), or Application Specific Integrated Circuits (ASICs).
-
product
Core Flow
Quizix Precision Pumps and Formation Response Testers (FRT’s) are the industry standard for core flow studies by operators, service organizations and research laboratories.
-
product
Custom Detectors
Besides the described types Inphora can supply detector-filter combinations with parameters matching the customer's special requirement, with different sized housing, without housing. If the application determines the detector's spectral responsivity, we can achieve that with a filter designed exactly to the specifications. CCD cameras with unusual spectral sensitivity functions can be matched with filters to obtain CIE tristimulus response or photopic response. Similarly, photmultiplyers can be matched also with INPHORA filters. When determining parameters for a custom detector-filter combination several details have to be considered:
-
product
Cyber Drill And Blue Team Exercise Stimulation
LGMS Security Team will approach the Cyber Drill as a simulation of the possible occurrences during a cyber incident. Based on the defined scenario, LGMS Security Team will perform a technical simulation so as to accurately capture the responses of client’s team in responding to such incidents.In order to obtain the best results, LGMS Security Team will only use information that can be obtained either through public information or by any means of deception techniques.
-
product
Data Acquisition Processor Board
DAP 5000a
When your application needs Pentium-powered real-time processing under Windows, choose the DAP 5000a. Even at maximum sampling rates, the combination of a fast processor with low latency allows computation in real time between samples – and on-time response for control applications.
-
product
DC Measurements
Standard Windows sound cards do not respond to DC or frequencies lower than a few Hz. (See Why Sound Cards Block DC Signals below for explanation.)There are two general approaches to get true DC response from a standard sound card: Modify the card, or add an external circuit to convert the DC into an AC signal which can be easily measured by an unmodified card.
-
product
Detectors
Sanwa Electric Instrument Co., Ltd
A device or instrument designed to detect the presence of a particular object or substance and to emit a signal in response.
-
product
Device Current Waveform Analyzers
The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.
-
product
Digital/Analog Frequency Response Analyzer
8800 Series
The analyzer utilizes a digital “Sync” signal to provide synchronization between analog and digital hardware. The Model 8800 performs simultaneous analysis on both analog input channels and digital target processor, reliably capturing all data. Versatile by design, the Model 8800 digital interface can be disabled, via software, to use the analyzer in a standard 2-channel, analog-only configuration.
-
product
Digital Circuit Breaker Analyzer
CT-3500 S2
The CT-3500 S2 is Vanguard’s second generation, stand-alone, digital, microprocessor-controlled, circuit-breaker timer. It measures the elapsed time from the instant a breaker coil is energized to the instant of opening or closing of a circuit-breaker’s dry contacts. In addition to timing a breaker’s contact response time, the CT-3500 S2 can also time relays or other switching functions that use an initiating trigger voltage (24-300 Volts DC or AC). The timer-triggering voltage starts three independent electronic timers. Each timer is individually stopped by its respective dry-contact closing or opening. The CT-3500 can fully analyze the timing of all circuit breaker operations (Open, Close, Open – Close, and Close – Open). Timing results are displayed in milli-seconds and cycles on the unit’s back-lit LCD screen and can be printed on the built-in 2.5-inch wide thermal printer.
-
product
Digital Humidity & Temperature Meter
DL7102
A compact probe size, with combined humidity and temperature meter.Ideal for field use offering high accuracy and fast response measurement.The addition of dew point and wet bulb reading makes this a truly versatile instrument.
-
product
Digital Panel Mount Load Cell Meter
MODEL DPM-3
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
product
DisplayMate Multimedia with Motion Bitmaps Edition
DisplayMate Technologies Corporation
DisplayMate Multimedia with Motion Bitmaps Edition includes a Motion Engine that moves a special set of test patterns and test photos to measure and evaluate response time, motion blur and motion artifacts in displays for different speeds, directions, intensities and colors for all monitors, projectors and HDTVs. It has everything in the standard Multimedia Edition including all of its 500+ test patterns up through 3072 x 3072 resolution.
-
product
Distance Sensor Technology
Photoelectric sensors
Our distance-measuring photoelectric sensors work according to the triangulation or propagation time measurement principle, with a red light or laser. The highly compact sensors have wide measuring ranges and measure very accurately with short response times.
-
product
Double Bellows Differential Pressure Switch
DP
Two opposing bellows in the Model DP differential pressure switch result in maximum sensitivity, quick response to changes and good vibration resistance. Choice of brass or 316 stainless steel assures broad media compatibility. Setpoint adjustment is easy thanks to external knobs and large, clear scale reading directly in psid.
-
product
Downconverter for the 21cm Bandvalon
2100
1440MHz inputLow noise figure LNA 0.3dB 20 KHigh gain >40dB8-pole ceramic dielectric input filterHigh dynamic range, low-spurious responses Rugged milled aluminum housingRFI shielded constructionDesigned for use with Valon 5009 as LOSuitable for hydrogen line observation and general radio astronomy in the 21cm band.6Vdc @ 400mAIncludes 20” dc power supply cable
-
product
Dual 10th Order Lowpass Filter
64-VBF
The 64-VBF 10th order Lowpass Filter is a dual channel filter with independent switch settable Cutoff Frequency (Fc). The filter has a linear phase DC accurate root raised cosine response. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues. The output can drive a high speed DAQ multiplexer with its fast settle and capacitive drive capability.
-
product
Dual Accelerometer
M6
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
product
EIS Interface (Electrochemical Impedance Spectroscopy)
BATT470m
The BATT470m electrochemical impedance analysis interface (EIS) provides an easy to use battery/cell impedance test platform for the electrochemical industry. Utilizing the highly accurate PSM3750 frequency response analyzer from N4L, the BATT470 provides impedance measurement of batteries/cells up to 100V DC. With a frequency range of 100mHz to 1MHz, the BATT470m covers a wide range of applications. Our software package - PSMComm2, featuring “EIS” mode, displays the in-phase and quadrature impedance of the cell in Nyquist form as well as overall impedance (Z), in bode form.
