Showing results: 1081 - 1095 of 2618 items found.
-
ChenYang Technologies GmbH & Co. KG
is a sophisticated Hall Effect Gear Tooth IC featuring an on-chip 12-bit A/DConverter and logic that acts as a digital sample and hold circuit. A separate 6-bit D/A converterprovides a fixed hysteresis. The sensor does not have a chopper delay. It uses a single Hall platewhich is immune to rotary alignment problems.
-
Renesas Electronics Corp.
High-speed CMOS output photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a CMOS output IC on the output side. This coupler is a high common mode transient immunity (CMR), high-speed CMOS output type device designed for high-speed logic interface circuits.
-
EE105T-xx -
Executive Engineering
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
ZD500 -
Teledyne LeCroy
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Silent Solutions LLC
As wireless continues to be a significant growth opportunity, SILENT works with commercial and industrial manufacturers to ensure time-to-market for RF and wireless enabled products. We design, build, and test RF and wireless solutions - within budget and cost guidelines - for consumer grade products and high performance circuits and systems.
-
30056 -
Parallax Inc.
The Flexiforce sensor features a pressure sensitive disc pad on the end of an ultra-thin (0.008 in.) flexible printed circuit ribbon that can be easily integrated into force measurement applications. Note that the flexible ribbon is to accomodate optimal placement of the pressure-sensitive disc; the sensor does not measure force applying curvature to the ribbon itself.
-
GCP-MG -
proconX Pty Ltd
GCP-MG is a next-generation Modbus/CAN gateway specifically designed to interface Woodward's GCP-30 series genset controls (GCP-31, GCP-32), and LS 4 circuit breaker controls with Modbus networks. The GCP-MG gateway has been developed in cooperation with Woodward to ensure the highest possible degree of interoperability with Woodward equipment.
-
MAG-450 -
MCH Instruments Co.,Ltd.
Features:*Advanced circuit design with imported components ensure minimum accuracy deviation.*Signal frequency:100kHz~150MHz, 3 harmonic up to 450MHz*Output wave form:sine and amplitude-modulation wave*RF/AM output, max, intensity≥10Vp-p*External modulation signal can be set between 50Hz~20kHz
-
72-6792 -
Tenma
*Electronically locates hidden cables gas and water pipes*Traces hidden ceiling joists and wall studs*Senses presence of mains power withut touching live wires*Locates breaks in circuits and cables*Identifies faulty plugs switches and sockets*Incorporates audio signal and indicator light
-
SFY027 -
Shanghai Launch Electric Co., Ltd.
Microcomputer automatic control, all keyboard operation, convenient man-machine conversation function, detector signal switch through the time of preparation proceduresHighly stable circuit control system to ensure a high reliability of the instrumentPerfect overheat protection for column box and detectorStorage in ten seconds the file of parameters analysisStopwatch
-
5085 -
Abaco Systems Inc
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
Circuit Check, Inc.
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Tripp Lite
Tripp Lite's Multi-Functional Network Cable Tester allows you to test wiring continuity for Cat5, Cat6, Phone and Coax cable assemblies. Identifies mis-wires, short circuits and open circuits. Features two piece transmitter and receiver, two BNC-F coax converters and coax terminator. Includes handy storage pouch when not in use. Power supplied by 9V Battery (not included).
-
National Technical Systems
Fourier Transform Infrared Spectroscopy (FTIR) is a standard technique used in the identification of contaminating materials on the surface of printed circuit boards (PCBs) and around the leads of electronic components (BGA, capacitors, resistors, inductors, connectors, diodes, oscillators, transformers, IC, etc.) on printed circuit assemblies (PCAs). Additionally, FTIR can be used for “simpler” identifications, such as determining a specific type of plastic or rubber compound.
-
M-800P -
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Model 800P is the world’s first clamp meter which can detect smallDC current in AC circuit in addition to general AC/DC current measurement.*By using this clamp meter, DC offset surveillance can be madeeasily in the actual fields like as solar inverters, etc. and it is possibleto check if the DC component in AC circuit is less than 1% ofthe rated AC current or not, according to the regulation.