Showing results: 436 - 450 of 2707 items found.
-
-
MPI-502 -
Sonel S.A.
Short circuit loop parameters measurements:measurements of short circuit loop impedance in networks with rated voltage: 220/380 V, *230 V/400 V, 240/415 V and frequency 45...65 Hz,*measurements of short circuit loop impedance with current 15 mA without tripping the circuit breaker.Testing the RCD breakers of AC, A types:*testing of prompt, short-delay (general) and selective RCDs for the rated current values 10, 30, 100, 300, 500 mA,*IA measurement*RE and UB measurement without tripping the circuit breaker,*extended RCD test function AUTO, with measurement of ZL-PE with current 15 mA - measurement of IA and tA during one RCD tripping.Detection of the replacement L and N in the socket and automatic conversion in the meter.Low voltage resistance measurements of protective circuits and junctions:*measurement of resistance with ±200 mA current*calibration of test leads - possibility of using any length of test leads,*low current resistance measurement with accoustic signalling
-
8022 -
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges.
-
Z-Axis Connector Company
Z-AXIS Flex Circuit Test Fixtures are used to connect flex circuits to test equipment. 20,000 plus cycles. Using the Z-Axis Elastomeric Connector Interposer, the connection to the OEM FFC connector becomes permanent and is thereby saved from over-use.
-
Model 62-1 / 62-2 -
Telebyte, Inc.
FEATURES: Supports 10 Category I & 3 Category II Circuits; Full EIA-530 & RS-422 Compliance; DTE & DCE Models; Meets MIL-STD-188-114 Type 1/2; Up to 256 KBPS Data Rate. Conversion between RS-232 and EIA-530 is accomplished by the Models 62-1 and 62-2. These devices provide conversion for the entire EIA-530 interface which includes ten Category I circuits and three Category II circuits.
-
Wewon Environmental Chambers Co, Ltd.
IC welding to PCB, IC is integrated in the chip general purpose circuit, it is a whole. Once the inside is damaged, the chip will be damaged. The goal of printed circuit boards (pcbs) is to connect IC and discrete components to form a larger working circuit. Thermal cycling equipment can detect the defects and hidden dangers of welding components in the production process, decreasing failure rate. When it fails, components can be replaced in timehttps://www.wewontech.com/thermal-cycling-test-equipment/
-
BE9000 Series -
Berry Test Sets
The BE9000 is a portable AC powered test set for use at almost any point in a circuit on the customer premises location (PBX or station equipment) to the Central Office. The BE9000 is able to accommodate a wide range of circuit types such as: DS1, DS0, DDS and all 2Wire or 4 Wire analog Special Circuits. Maintenance and installation of these circuits requires a combination of these functions: DS1 performance monitoring, DS1 BERT, DS0 BERT, Drop & Insert, Transmission, Signaling, Ringing, Addressing and Supervision in one test set to achieve maximum technician efficiency. Additionally, the set can be programmed in the field so that repetitive tests can be stored and recalled for future use.
-
230 -
Electronic Specialties Inc.
Short Buddy helps you find the short! This unique tool connects at the fuse panel and becomes in series with the test circuit. A system of audible beeps helps you find the problem and permit hands free troubleshooting. Have a dead short? Short Buddy gives you continuous re-set/re-power capability, a real time saver. While you push, pull, tug and grab wires, Short Buddy is always watching the current level. If your tug causes the dead short again, Short Buddy opens the circuit for 10 seconds, then re-applies power to the circuit. Re-powering the circuit can also be done manually.
-
Hilkar
Current Limiting Reactor (CLR) is one of the most effective short circuit current limiting devices. It reduces stresses on busses, insulators, circuit breakers and other high voltage devices. Use of CLR is the most practical and economical approach at current limiting.
-
377C01 -
PCB Piezotronics, Inc.
Performance:Nominal Microphone Diameter:1/4"Open Circuit Sensitivity 2.0 Open Circuit Sensitivity (3 dB)-54 dB re 1 V/PaFrequency Range Inherent Noise<35 Temperature Coefficient of Sensitivity (+14 to +122FHousing Material: Stainless Alloy
-
Hilkar
Current Limiting Reactor (CLR) is one of the most effective short circuit current limiting devices. It reduces stresses on busses, insulators, circuit breakers and other high voltage devices. Use of CLR is the most practical and economical approach at current limiting.
-
Rockwell Automation
Our signal interface products provide signal conversion and electrical isolation between sensors and other field devices and a control circuit. Intrinsic safety modules add Zener diodes, which limit the amount of electrical energy on intrinsically safe circuits.
-
all-sun
is an embedded circuit; it converts unregulated AC into a constant DC. With the help of a rectifier it converts AC supply into DC. Its function is to supply a stable voltage (or less often current), to a circuit or device that must be operated within certain power supply limits.
-
Mors Smitt Group
Operating records for overhead power lines reveal that most faults are of a transient nature (e.g. lightning induced) & that service interruptions may be minimized by use of automatic reclosing of circuit breakers. An automatic reclosure of the circuit breaker, after the fault clears, provides improved service continuity & system stability. The 1B230 Series Reclose Relay provides for single or double shot automatic reclosing of circuit breakers, following interruption of supply due to a fault in the system.
-
R1L-BR -
TEGAM Inc.
The R1L-B series Ohmmeter/Bonding Tester is a digital microohmmeter designed to measure resistances from 10 to 20 . It is used in applications such as metal bonding, switch, circuit breaker, circuit resistance and other contact and connection resistance tests as well as higher resistance measurements for circuit analysis and resistor testing up to 20 . The instruments utilize the four-terminal, Kelvin technique to eliminate errors caused by the resistance of the leads. Resistance readings are viewed on a 3 1/2 digit display,