Showing results: 841 - 855 of 2707 items found.
-
LT45 -
Trailer Light Tester
The LT45 tester performs both light & electric brake function testing. It incorporates a digital display for checking voltage and current draw of tested circuit. This tester is powered by an internal battery.
-
MCL-3000D -
MULTI MEASURING INSTRUMENTS Co., Ltd.
This handy type clamp tester has the biggest CT window in the world (108mmx128mm) and can measure AC load current (0.01A -3000A) just by clamping the conductor without disconnecting the circuit.
-
Zero Defects International LLC
2D and 3D X-Ray Inspection services are available through the ZDI/Viscom applications center in San Jose. These services are especially valuable for failure analysis of failed or returned printed circuit assemblies.
-
K-280 -
The Eastern Specialty Company
TESCO Knopp’s K-280 Single Phase Socket Tester is designed to detect short circuits, backfeed and wiring errors in a 120/240 volt, 3-wire, single phase self-contained meter socket.
-
Picoprobe
The GGB Industries MULTI-CONTACT WEDGE allows for more chip design flexibility because it is custom configured to your circuit. Four Wedges can be used at the same time to probe a complete chip.
-
MS 2001 -
Meltronics Systemtech
This system is used to acquire Bi phase and DM signals from aircraft and records into FLASH memory. System has automatic frame synchronization and it is achieved through in built hardware circuit.
-
HNC Test Fixture -
Circuit Check, Inc.
Circuit Check continues to be a leading edge provider of custom engineered test solutions with our new Keysight i3070 HNC test fixture. Working with Keysight Technologies during the development of their HNC adapter in 2011, we were the first test fixture provider to offer customers with a solution to test large node count boards. High node count test fixtures can handle greater than 10,000 probes.
-
The Chameleon -
Circuit Check, Inc.
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
Chauvin Arnoux Metrix
Are designed for measuring leakage current diverted towards the earth. It enables the fault to be located or anticipated without disconnecting the equipment linked. It is specially designed to detect low fault currentson power circuits.
-
Coda Systems Ltd.
Low profile, short travel test probes for restricted space applicationsApplications where long travel is not required such as thin film/hybrid circuits or bareboard PCB testingReplaceable test probe by use of a receptacle
-
3662-5 -
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
3662-2 -
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
3797 -
VECTOR Electronics and Technology, Inc.
30 Gold plated edge contacts (15 each side)on 0.156"(3.96mm) centers.Convenient easy-to-read hole marking legend on both sides.No circuit pattern edge contacts only.
-
EM-6980 | 20 Hz – 50 KHz -
Electro-Metrics Corp.
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
EM-6981 | 9 KHz – 110 MHz -
Electro-Metrics Corp.
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.