Showing results: 991 - 1005 of 2707 items found.
-
Applied Relay Testing Ltd.
General purpose calibration/diagnostic tool.Built in precision resistors.Simple manual contact/routing/resistor selection.4mm terminal posts on key device connections.In line mode to aid fixture wiring/DUT debugging.Comprehensive documentation including circuit schematics.Connecting cables.
-
National Technical Systems
Conductive Anodic Filament (CAF) testing helps to determine the reliability of a printed circuit board (PCB) laminate material or a finished product. With conductor spacing and overall part sizes getting smaller and smaller, the necessity for this test is increasing.
-
HW Test
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
CCM1095 and CCM2096 -
Teledyne RF & Microwave
The CCM1095 and CCM2096 are power amplifiers that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.
-
LCI™ -
ndb Technologies Inc.
The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.
-
Pro-Check 720 -
LITE-CHECK LLC.
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault.
-
WR14 -
Raytech AG
Raytech's Digital Winding Resistance meter WR14 is the battery powered version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy measurement of very low resistance of any inductive loads.
-
ZET 7010 -
ZETLAB Company
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Acroname, Inc
LEAN AND MINIATURIZED PRODUCTION TESTING: With its ultra-small footprint, the MTM-Load-1 is engineered for load-testing of battery chargers, amplifiers, USB power outputs, and motor driver circuits. Ideal for functional testing in production or validation test environments.
-
FFR1000 -
Rhesca Co., Ltd.
This equipment is designed to bend a flexible printed circuit board, which has a high degree of freedom and versatility, and at that time, apply a load to the bending point at the initial stage or each time, and repeat bending and unfolding to confirm the durability.
-
WXU -
CKD Corporation
An integrated unit that integrates the flow sensor and valve of the circulation circuit of the cooling water.The complicated piping design around water and the number of man-hours for piping work are greatly reduced, and the footprint is reduced by 80% to save space in the system.
-
Mors Smitt Group
Test Block system is an evolution of the 14 test circuit versions widely employed in the power utility sector. The primary difference is the incorporation of ‘finger safe’ test sockets which allow the use of shrouded 4mm banana plugs.
-
Carl E. Holmes Company
SCRs and Diodes are used in the power sections of various power systems. A SCR Diode Tester is an important piece of equipment to determine if a SCR or a diode is defective in a power circuit. It is difficult and time-consuming to troubleshoot SCRs and Diodes with a digital meter.
-
Desco Industries, Inc.
Connects to utility ground when plugged inQuick, easy installation and grounding of both wrist straps and table mats.Tests entire circuit - wrist strap, cord and skin contactReliable resistance testActs as common point ground for the worksurface
-
1934B -
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Detect faulty wiring in 3 wire receptacle.*Test for GFCI receptacle for proper operation, 110-125V circuits.*Various combinations of three lights tell if wiring is correct or six possible faulty conditions.