Showing results: 1306 - 1320 of 2707 items found.
-
5085 -
Abaco Systems Inc
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
NI
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
NTN -
FuG Elektronik GmbH
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
Pacific Millimeter Products
These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.
-
ENVIROMUX-PT3-600 -
Network Technologies Inc
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
Circuit AOI 4.0 -
Machvision
Circuit AOI 4.0 is a set of industry-standard, automated precision inspection systems that combine precision, robust construction and line-of-sight technology for assembly and production under stringent regulatory standards and is ideal for PCB / HDI line inspection.It uses innovative alignment detection logic to detect defects such as short / open circuit, protrusion / depression, scratch, pinhole, residual copper, line width / line distance violation, missing objects, unwanted objects, and so on. The system can be used with off-line set-up station and off-line re-check station to enhance the detection capacity.Circuit AOI 4.0 uses multi-angle LED light source, compared to the traditional single angle light source design, can obtain the best image contrast, widely used in different plate inspection.
-
TS-217 -
Marvin Test Solutions, Inc.
The TS-217 is an I-level and Depot-level Universal Launcher test set supporting fighter aircraft launchers including the LAU-127, LAU-128, and LAU-129 (AMRAAM), LAU-117 and LAU-88 (Maverick), and LAU-7 (Sidewinder) missile launchers, launcher electronic assemblies, launcher power supplies, and circuit cards. The TS-217 is also used as a depot-level tester for F-18 armament including launchers (LAU-127, LAU-7, LAU-115, and LAU-116), bomb racks (BRU-32), and aircraft pylons (SUU-62 and SUU-63). Additionally, the TS-217 supports MAU-169 Paveway kits, subassemblies, and circuit cards. The TS-217 performs full parametric functional testing as well as troubleshooting to the faulty LRU (I-Level configuration) and SRU (Depot-Level configuration). The TS-217 can be used as an I-Level tester or as a Depot / Acceptance tester for launcher subassemblies.
-
1131 IN -
Standard Electric Works Co., Ltd
● Hight quality Taut Band movement.● Three insulation test voltages (DC) : 250V, 500V, 1000V.● Two ranges for continuity test : 2Ω & 20Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600Vac.● 200mA continuity short-circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
CWTMini50HF -
Power Electronic Measurments Ltd
For high-speed and high power-density power electronic applications. This higher bandwidth probe is ideal for measuring the faster current transients in today’s new semiconductor technologies where faster turn on and turn off times, higher blocking voltages and smaller circuits demand, smaller, higher temperature, faster current probes.
-
PentaLogix
SO-9001 and UL certifiedClass IIIRigid circuit boards up to 40 layers3-mil traces and 3.5 mil spacesMinimum Mechanical drill size 8-milMinimum Laser drill size 3-milBlind / Buried ViasControlled ImpedanceRoHS Compliant (all options available)High temperature, high frequency materialAluminum and other exotic material
-
CB120MG-CM -
XIMEA GmbH
4K, compact, high speed camera for: Flat panel inspection (FPD), printed circuit board (PCB) examination, solar panel analysis, persistent stadium and border security, wide area surveillance, cinematography, sports and entertainment, 360 panorama, UAV and Autonomous, Unmanned vehicles, aerial or city mapping.
-
Model W4.0 x L6.5 -
D-COAX, Inc.
This portable manual probing station is designed for a versatile, comfortable, and accurate operation on up to 4.0” wafers or 4.0” X 6.5” printed circuit board assemblies. This turn-key, manually operated probing station, model W4.0 x L6.5, is part of the D-COAX commitment to the test and measurement and PCB fabrication industries.
-
AMETEK Sensors, Test & Calibration
Today we have the most complete line of components and accessories for precise circuit control; no one else comes close. We design, engineer and provide technical support with on-site staff. With in-plant stamping, machining, welding, painting and assembly, we have control over our parts and processes.
-
TT40 Series -
Systems Engineering & Management
The TT40 series of airborne dual power (.25/2 W) telemetry transmitters are designed to transmit data in the frequency bands covering 1435-1540, 1710-1850, or 2185-2485 MHz. These transmitters are true FM, modular, all solid state and are protected for operation into any VSWR, without damage, including open or short circuit.
-
eloZ1-400 -
elowerk Testsystems
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the very latest generation, reliably detecting connection and assembly faults on printed circuit board assemblies. The eloZ1-400 is the compact version of the eloZ1. It is particularly suitable if there is only limited space to fit test appliances. The eloZ1-400 can also be used as a mobile test system.