Showing results: 136 - 150 of 217 items found.
-
DR1000 -
Electro-Sensors, Inc.
Features • Works with remote / external pulse frequency output sensor (NPN, PNP, or Mag Pick-up) • DPDT relay output • Under-speed setpoint adjustment from 0.5-5,000 rpm (at 8 PPR) • Terminal blocks for easy wiring • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • Rugged explosion proof / NEMA 4X housing • UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
CTS Series -
Continental Control Systems LLC
The CTS series CTs are available with windows from 0.75 inch up to 2.0 inch. They have a removable section, so that they can be installed without interrupting the circuit. 0.333 Vac output at rated current Accuracy ±1% from 10% to 100% of rated current Phase angle <2° degrees at 50% of rated current (valid for 70 A or higher) 8 ft. twisted-pair wire, 600 Vac rated UL recognized for voltages up to 600 Vac, CE mark, RoHS
-
CR MAGNETICS, INC.
CR Magnetics supplies an extensive line of toroidal current transformers for any need. Our offerings include measuring from 10,000 amps to a few milliamps. This includes ANSI, Commercial, Ground Fault, High Frequency, Wound Primary, DC Immune and Nano Alloy current transformers. Various outputs include 5 amp secondary, high turns ratio voltage outputs for both wire leads and pcb configurations. Our products are UL Recognized for both US and Canada.
-
Testifire 2000 -
SDi
Testifire is the world's first multi-stimulus detector tester for smoke, heat and CO fire detectors. It enables faster and more efficient testing of both single and multi-sensor detectors. There are two models available Testifire 1000 for testing smoke and heat and Testifire 2000 for testing smoke, heat and CO. Testifire is the result of several years of technological development and as a result is by far the most advanced tester available. Testifire is UL certified and is approved by leading detector manufacturers from around the world.
-
Testifire 2001 -
SDi
Testifire is the world's first multi-stimulus detector tester for smoke, heat and CO fire detectors. It enables faster and more efficient testing of both single and multi-sensor detectors. There are two models available Testifire 1000 for testing smoke and heat and Testifire 2000 for testing smoke, heat and CO. Testifire is the result of several years of technological development and as a result is by far the most advanced tester available. Testifire is UL certified and is approved by leading detector manufacturers from around the world.
-
TESTIFIRE 1001 -
SDi
Testifire is the world's first multi-stimulus detector tester for smoke, heat and CO fire detectors. It enables faster and more efficient testing of both single and multi-sensor detectors. There are two models available Testifire 1000 for testing smoke and heat and Testifire 2000 for testing smoke, heat and CO. Testifire is the result of several years of technological development and as a result is by far the most advanced tester available. Testifire is UL certified and is approved by leading detector manufacturers from around the world.
-
CX-Z11 -
Shenzhen Chuangxin Instruments Co., Ltd.
The Fingernail Test Probe is used to test to IEC 60335 and UL standards. It checks the security of parts that snap together. The spring loading in the handle can be calibrated to the force necessary to use the instrument. This probe is made of stainless steel with specially hardened tip and a Delrin?handle. Handle has a threaded hole for use with force gauges.
-
228 -
Simpson Electric Company
Test for dangerous leakage current with the Simpson Model 228, designed to meet the latest UL, IEC, and ANSI specifications. The 228 detects both AC and DC leakage current and simulates human response at three different levels -- reaction, let-go, and burn hazard. Each Model 228 comes with test leads with alligator clips, manual, and batteries.
-
SCP1000/SCP2000 -
Electro-Sensors, Inc.
Features• Internal sensor• Over-or under-speed config., 1-990 rpm• 1 DPDT relay output (SCP1000), 2 SPDT relay outputs (SCP2000)• Built-in start delay• Dial-in calibration does not require power• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Works with Electro-Sensors magnetic pulser discs / wraps• Explosion proof housing• UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
UDS1000 -
Electro-Sensors, Inc.
Features • Works with remote / external quadrature pulse frequency output sensor / incremental encoder (NPN or PNP) • DPDT relay changes state when shaft direction reverses • Reverse-over-speed setpoint adjustment from 0.5-5,000 rpm • Relay resets when reverse motion stops • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • Explosion proof/NEMA 4X housing • UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
CX-75 -
Shenzhen Chuangxin Instruments Co., Ltd.
The Finger Nail Probe is indicated test IEC60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the neccessary force for using the instrument. This probe is make of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.
-
CX-Z12 -
Shenzhen Chuangxin Instruments Co., Ltd.
The Finger Nail Probe is indicated to test IEC 60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the necessary force for using the instrument. This probe is made of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.
-
Extech MA260 -
Extech Instruments Corporation
The MA260 is a True RMS 200A AC Open Jaw Clamp Meter. The MA260 has a built in NCV detector and can measure up to 200A in its 0.6 in. open jaw. True RMS for accurate readings of noisy, distorted or non-sinusoidal waveforms. Complete with test leads and two AAA batteries. UL listed with a CAT IV 600V safety rating.
-
RT110 -
Klein Tools, Inc.
Light sequence indicates correct/incorrect wiring.Conforms to UL Std 1436, Certified to CSA Std C22.2 #160.Operating temp: 32°F to 140°F (0°C to 40°C).Built to withstand a 6.6 ft. (2m) drop.Nominal Voltage: 110/125V AC at 50/60Hz in 3-wire outlet.Designed to detect the most common wiring problems in standard receptacles.
-
Models M100BVS5 & M500BVS5 -
Rod-L Electronics
Now you can perform safe, rapid and efficient hipot testing, ground continuity testing, and total or real current monitoring in one simple operation. The ROD-L Electronics model M100BVS5 and model M500BVS5 hipot testers perform safe and accurate AC hipot and ground continuity testing in compliance with UL, IEC, CSA, VDE, FCC and other electrical equipment testing standards