Filter Results By:

Products

Applications

Manufacturers

PC

Checking personal computers and using a pc as host to perform test.


Showing results: 796 - 810 of 1612 items found.

  • Dual Channel Arbitrary Function Generator With 40 To 240MHz Models

    TGF4000 Series - Aim-TTi

    The TGF4000 series of function/arbitrary generators offers signal generation capability up to 240MHz on two identical full performance channels that can operate independently or in coupled or tracking modes. Precise channel to channel phase control with a resolution of 0.001° is provided. A wide range of built-in waveforms is included and custom arbitrary waveforms can be used at sample speeds up to 800MS/s and replay rates up to 80MHz. PC based arbitrary waveform generation and editing software is provided.

  • Environmental Test Chamber

    Lisun Electronics Inc.

    The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip.The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1 and humidity is 0.1%R.HThe temperature sensor is platinum PT100 Ohms/MV resistor

  • Fifo Serial Analyzer 2 TO 2 Breakout Box

    FLL222 - Fifo Electronics

    The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.

  • Fluid Level Sensor

    McLAREN Applied Technologies

    The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.

  • Force and Displacement Monitoring

    burster präzisionsmeßtechnik gmbh

    Measuring accuracy of up to 0.05 %, sampling rate 10 kHz maximal, innovative evaluation elements, i.e. windows, thresholds, trapeziums, envelope curves, freely definable mathematical operations, two synchronous processes can be monitored, 128 measuring programms, intelligent Signal sampling, programmable I/O functions, Ethernet, USB, RS232, extensive diagnostics and statistical analysis, all usual sensor interfaces, variable fieldbus interfaces, powerful PC Software

  • Load and Displacement Monitoring

    burster präzisionsmeßtechnik gmbh

    Measuring accuracy of up to 0.05 %, sampling rate 10 kHz maximal, innovative evaluation elements, i.e. windows, thresholds, trapeziums, envelope curves, freely definable mathematical operations, two synchronous processes can be monitored, 128 measuring programms, intelligent Signal sampling, programmable I/O functions, Ethernet, USB, RS232, extensive diagnostics and statistical analysis, all usual sensor interfaces, variable fieldbus interfaces, powerful PC Software

  • Process Control Instruments

    burster präzisionsmeßtechnik gmbh

    Measuring accuracy of up to 0.05 %, sampling rate 10 kHz maximal, innovative evaluation elements, i.e. windows, thresholds, trapeziums, envelope curves, freely definable mathematical operations, two synchronous processes can be monitored, 128 measuring programms, intelligent Signal sampling, programmable I/O functions, Ethernet, USB, RS232, extensive diagnostics and statistical analysis, all usual sensor interfaces, variable fieldbus interfaces, powerful PC Software

  • Rack Mount Osprey Chassis 4-Slot Unibus

    0249-U - Strobe Data Inc.

    10.5" high by 19" wide by 20" deep (267 x 483 x 508 mm), this chassis is FCC certifiable**. AT style motherboard, 3 x 5-1/4" bays, 2 x 3-1/2" bays. Cooling fans and space are included for user's hex-height, 4-slot DD-11 Unibus backplane, PC motherboard, diskette and hard drives (one hidden and four visible half-height bays).

  • Watchdog Timer Card

    PCI-WDG-CSM - Acces I/O Products, Inc.

    This multifunction card contains a watchdog timer. Additionally, one or more options may be included on your card. These are: a computer power supply monitor, a computer internal temperature monitor, an optional capability to read the temperature, a fan-speed monitor, and an on-card buzzer to signal watchdog timeout. PCI-WDG-CSM continuously monitors critical PC functions. When a fault occurs, the card automatically generates outputs that can be used either to initiate corrective action or to generate alarms.

  • 3-in-1 Analyzer: Logic Analyzer, Protocol Analyzer, Simple DSO

    MSO2216B+ - TEAM SOLUTIONS, INC.

    3-in-1 Analyzer : Logic Analyzer, Protocol Analyzer, Simple DSO• PC-based, USB3.0 interface• 8 / 16 Channels(display digital and analog waveforms of the same channel)• Digital Inputs : 2 GHz Timing, 200MHz State Analysis (Max.)• Analog Inputs : 200 MS/s (Max.), Bandwidth 40 MHz• 8 Gb Memory (Max.)• PC RAM storage for streaming mode• Utility model patent of Taiwan number M601827

  • 3-in-1 Analyzer: Logic Analyzer, Protocol Analyzer, Simple DSO

    MSO2216B - TEAM SOLUTIONS, INC.

    3-in-1 Analyzer : Logic Analyzer, Protocol Analyzer, Simple DSO• PC-based, USB3.0 interface• 8 / 16 Channels(display digital and analog waveforms of the same channel)• Digital Inputs : 2 GHz Timing, 200MHz State Analysis (Max.)• Analog Inputs : 200 MS/s (Max.), Bandwidth 40 MHz• 8 Gb Memory (Max.)• PC RAM storage for streaming mode• Utility model patent of Taiwan number M601827

  • Bore Gauges Xtreme 3 Digital Smart

    Sylvac

    • Great measuring range (2 - 300 mm)• Integrated Bluetooth® technology• Blind bore measurement from 2 to 6 mm and from 12.5 mm• Fixed anvils• UKAS certificate included with all rings• UKAS certificate included with each instrument• Manufactured according to DIN863• Memorization of 4 ring gauges values• Water and coolant resistant, protection rating IP67 according to IEC 60529• Programmable by PC• S_Connect Proximity

  • Noise Dosemeter

    Castle GA257B - Castle Group Ltd.

    The SONUS Pocket Dosemeters are designed to be powerful and easy to use. These dosemeters are small and tough so measurements and data can be collected throughout the working period. Data can be reviewed on screen or downloaded to a PC for further analysis. The SONUS GA257B is a dedicated basic dosemeter fully compliant with IEC 61252:1993 and IEC 61672-1:2013, giving simultaneous sound exposure (Lep'd) and maximum peak (Zpeak) measurements, an essential feature for Noise at Work Regulations assessments.

  • Function Generator

    FG-281 - Texio Technology Corp.

    The FG-281 is a function generator using DDS (Direct Digital Synthesis) for superior frequency stability. Possible to output sign wave and square wave at wide oscillation range from 10mHz to 15Mhz. A 10-key keypad provides user-friendly operation even though various functions are available. Possible to memorize 9 kinds of panel settings and they can be recalled easily. RS-232C and GP-IB interfaces are available as standard and enable to be controlled by PC (full remote control).

  • Tilt Tables

    MTG3,MTG5 - D.Marchiori s.r.l.

    D.Marchiori (DMA) design and manufacture various models of Tilt Tables which provide very accurate position and motion control for testing and calibrating attitude/heading and inertial reference units. Tilt Tables can be supplied with different diameter support tables. Tilt tables can be controlled either by an internal computer or by an external PC connected via RS232. Tilt Tables are equipped with fast zero position finder. Speed, acceleration and position can be set independently for each axis.

Get Help