Showing results: 2401 - 2415 of 2843 items found.
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
DeltaTRAK
This reusable logger can monitor temperature and humidity in facilities, storage and processing areas, clean rooms, labs, and during transport. It is equipped with an external sharp tip probe, providing the option to monitor internal core temperature. Data is available in PDF or spreadsheet format and used for various purposes, such as process or equipment verification and validation, thermal mapping, and documenting environmental conditions to meet GMP, GDP and regulatory compliance. Reports are analyzed to identify trends and patterns, and management decisions can be made to improve practices in areas such as processing and cold chain logistics. Data is easy to archive for record keeping, audits, and compliance with FDA, CDC, HACCP, FSMA and other regulatory requirements.
-
PPTACT1CS -
Power Probe Group, Inc.
THE PROBE 12-Volt Test Light with Haptic Feedback, (PPTACT1CS) this tool vibrates and lights when voltage over 12 volts is detected. When a voltage is below 12 volts, this functions as a standard test light. Just push the button and go! Shows positive voltage, ground, and continuity “all in one tool” with haptic advantage.
-
MicroContact AG
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
Extech SDL900 -
Extech Instruments Corporation
The SDL900 is an AC/DC Magnetic Meter and Datalogger with automatic temperature compensation. The SDL900 utilizes Hall effect sensor. This meter features an adjustable data sampling rate from 1 to 3600 seconds. Complete with uniaxial magnetic probe sensor with protective cover, SD memory card, 6 AA batteries and hard carrying case.
-
QT2256-640 PXI -
Qmax Test Technologies Pvt. Ltd.
designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities for conventional PCBs.
-
T4111 -
COMET SYSTEM, s.r.o.
Transducer is designed for temperature measurement at C or F by means of an externaltemperature probe with Pt1000 sensor. Measured temperature is converted to linearized unified signal 4-20 mA. Measured values are displayed on LCD display. It is possible to switch OFF theLCD at all. Current loop has two-wire connection and requires power from evaluation device.
-
SemiProbe
SemiProbe has developed probe stations for a wide variety of optoelectronic and photonic device applications, including light emitting diodes (LEDs), vertical cavity surface emitting lasers (VCSEL) and photo diodes. Testing and handling small, fragile, thin wafers with thousands of die on them poses unique challenges that require innovative solutions.
-
PortaTest -
Schleich Gmbh
Portatesters are easy to use. Based on the test standard, you select the corresponding test sequence. Then, the required test probe and the electrode gap for the selected test standard is displayed. The setting gauge, included in the scope of delivery, facilitates the adjustment of the electrode gap. Afterwards you fill the insulating oil in the test vessel and close the test chamber.
-
ML675 -
Teledyne Monitor Labs
The Teledyne ML®675 dilution-extractive system can be used in 40CFR75, 40CFR60, 40CFR63, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.
-
SmartScan 350 -
Amber Precision Instruments
Reproducing similar soft or hard failure to the gun test - Flexible automatic failure detection module - Susceptibility map generation- Automatic report generation- Flexible scan area editor (SAE)- Flexible display (3D, histogram)- Matlab support- Expandability (EMI scan, phase measurement, NFFF transformation)- Custom design probes
-
KM 918 -
Kusam Electrical Industries Limited
* Dual display Temperature & Humidity* Accurate NTC sensor* Measures temperature in °C/°F* Dew point and Wet bulb Function* MAX MIN / MAX-MIN / AVG / & HOLD function* Portability and simplicity one-hand operation* Quick response R.H. sensor* Display Back-light* Auto Power Off* External probe* CE-Mark approval
-
all-sun
This hand-held digital logic probe provides convenient and precise use in the measurement of logic circuits. It displays logic levels (high or low), pulses and voltage transients down to 25 nanoseconds. High intensity LED readouts provide instant response to the logic state. Tests all logic families TTL/LSI, and CMOS/MOS digital circuits.
-
Yelo Ltd.
A test fixture or test jig is the component containing the bed of nails used for testing the PCB or assembled product. It is powered and controlled by the Yelo Testpoint system which has test cards capable of providing multiple test conditions. This system also controls the probes used in the bed of nails, and relays test information back to the Testpoint system to be analysed.
-
PPDCM80 -
Power Probe Group, Inc.
The Power Probe Digital Clamp Meter is an 80amp, auto-ranging clamp meter designed specifically for the automotive technician. This meter is rated CAT III 600V and can measure Volts, Amps, Ohms, Frequency and Temperature, necessary for automotive electrical testing. This meter’s diagnostic applications include (but are not limited to) Parasitic Draw, Crank Current testing and HVAC Temperature testing.