Showing results: 751 - 765 of 2826 items found.
-
SPM-8100FM -
Shimadzu Corp.
The new HR-SPM scanning probe microscope uses frequency detection. his instrument is not only capable of ultra-high resolution observations in air or liquids, but for the first time enables observations of hydration/solvation layers at solid-liquid interfaces.
-
Bumpy -
Electronut Labs
Bumpy is an inexpensive Open Source blackmagic probe compatible SWD debugger designed to be used with ARM GDB. It supports many platforms, but was primarily designed for use with our Nordic Semiconductor nRF BLE boards.
-
ACR Systems Inc.
An external Relative Humidity and Temperature Probe for tight or remote locations. Every RH reading is temperature compensated for accurate readings. For environmental susceptibility, see Data Logger specification. Maximum extension is 30m (100').
-
INGUN Prüfmittelbau GmbH
INGUN has an unbeatable assortment of test probes and test fixtures for individual testing tasks.Thanks to many years of experience in the testing equipment field, INGUN offers the suitable test solution for every test requirement.
-
DPO7OE -
Tektronix, Inc.
The DPO7OE series optical probes with a DPO70000 real-time scope deliver the performance and advanced debug capabilities designers need to fully troubleshoot 400G PAM4 signals, up to 56 GBaud, and reduce time to market.
-
HD320B2 -
Delta OHM S.r.L.
The probe measures the carbon dioxide concentration in air. It’s indicated for checking and monitoring the indoor air quality. Typical applications are the check of the air quality in all the buildings where there is a crowd of people (schools, hospitals, auditoria, canteens, etc.), in the working places to optimize the comfort. CO2 measurement is obtained with an infrared special sensor (NDIR technology: Non-Dispersive Infrared Technology) that, thanks to the use of a double filter and a special measurement technique, warranties precise, stable and long-term measurements. The air to check is spread inside the measurement chamber through the protection membrane placed at the top of the probe.
-
LPPAR01 -
Delta OHM S.r.L.
The LPPAR01 probe measures the ratio between the number of photons that strike a surfacein one second, in the 400 nm…700 nm spectral range and the surface area (m2). This quantity is defined as PAR: Photosynthetically Active Radiation.
-
LPPAR03… Series -
Delta OHM S.r.L.
The probe LPPAR03 measures the ratio between the number of photons that strike a surface in one second, in the 400 nm…700 nm spectral range and the surface area (m²). This quantity is defined as PAR: Photo-synthetically Active Radiation.
-
STI3000 -
Solidus Technologies, Inc.
The STI3000 is a wafer-level MEMS and mixed signal ASIC probe test system that combines several functional STI test equipment blocks for testing gyros, accelerometers, pressure sensors, microphones, resonators, and mixed signal ASICs.
-
HIOKI E.E. Corp
Sensitivity of Conventional Probes Deliver Precise Measurement of Low Current Waveforms from 1 mA. High-precision Current Sensors, DC to 4 MHz, DC to 20 kHz, up to 50 kHz and load current sensors,
-
CG-196 -
EverBeing Int'l Corp
Everbeing controlled environment probe station allows vacuum and cryogenic probing down to 77K with liquid nitrogen or high temperature probing up to 1273K. Efficient in characterizing your devices at extreme temperatures, vacuum, specific gas, etc.
-
LP471PYRA… Series -
Delta OHM S.r.L.
The LP471PYRA… probes consist of a pyranometer LPPYRA03, LPPYRA02 or LPPYRA10 equipped with the SICRAM module and a 5m or 10m cable for the connection of the pyranometer to the instruments HD31, DO9847, HD2102.2, HD2102.1 and HD2302.0, so to get the reading in W/m² directly on the instrument’s display.
-
DP Series -
Shenzhen Micsig Instruments Co., Ltd.
*Micsig DP Series High Voltage Differential Probes can be used with any brand of oscilloscope. *It adopts high-impedance isolation between the input and output to protect personal safety, converts the input high-voltage signal to a low-voltage signal for observation and analysis on oscilloscope.
-
AR RF/Microwave Instrumentation
The FL8000 Series field probes offer a three-in-one solution capable of measuring continuous-wave, pulsed, and modulated electric fields. Covering 5 kHz – 60 GHz, the FL8000 Series works great in commercial, automotive, military, and aviation applications.
-
Series S200, S300, S400, and S500 -
AlphaTest Corp.
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.