Showing results: 1276 - 1290 of 2843 items found.
-
-
GATS-3200 -
W.M. Hague Company
* Test individual packages or * Test Multi-image panels with Step&Repeat Function * single flying probe top using very high speed voice coil motor (VCM) technology * 50 - 100 tests per second ... high throughput * Dual Flying Probe Top for testing bump-to-bump nets * flying probe head allows testing of all nets including each power and ground point * 4-wire test capability
-
TPW24 -
Edsyn Inc.
Temperature Wire Probe K-Type 24 AWG x 5.5 ft.
-
N2782B -
Keysight Technologies
The N2782B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
-
RFP 3 -
Huber Signal Processing
The Active RF Probe provides a very low capacitive load of the system to be measured.
-
CT4121 -
Cal Test Electronics
The CT4121 is a compact FET probe with very high input resistance and low input capacitance. With a 1.2 GHz bandwidth, this probe is ideal for timing analysis or troubleshooting high speed logic circuits, for design verification of disk drives, as well as for wireless and data communication design. The CT4121 can measure up to ±40 V (DC + AC peak). Compatible with oscilloscopes from all major manufacturers, the probe is powered by the included 9 V battery or direct from the oscilloscope using the included USB power lead.
-
AP031 -
Teledyne LeCroy
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
10076C -
Keysight Technologies
The Keysight 10076C 3.7 kVpk, 100:1 passive probe gives you the voltage and bandwidth you need for making high-voltage measurements. Its compact design makes it easier to probe today's small power electronics components, and its rugged construction means it can withstand rough handling without breaking.
-
HDV7C-A2-39-HD-1 -
Extech Instruments Corporation
HD 2-Way Articulating 3.9 mm × 1 m Camera Probe for Extech HDV700-Series High-Performance Videoscope
-
ZS4000 -
Teledyne LeCroy
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.6 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS4000 is ideal for 2.5 GHz and 4 GHz oscilloscopes.
-
ZS2500 -
Teledyne LeCroy
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS2500 is ideal for 2.5 GHz and lower oscilloscopes.
-
PRB-HP-9060 -
TEAM SOLUTIONS, INC.
*Up to 60MHz*Includes a handy storage pouch and includes an IC test-hook adapter for the probe.*The BNC connector rotates to avoid cable tangle or kink.*Cable length is 1.4 meters.
-
ZD200 -
Teledyne LeCroy
With the ProBus interface, the ZD200 becomes an integral part of the oscilloscope. The probe sensitivity and offset are automatically optimized based on the oscilloscope gain settings, so control is transparent to the user. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
TCR-600 -
NAPSON Corp.
*Controlled Thermo-chuck (room temperature~600℃/less than 20 minutes)*600C compatible probe head with 1mm linear*Controlled with vacuum sensor, digital thermo-meter, vacuum gauge and gas flow meter*Temperature measuring accuracy:±(0.5% + 1℃)
-
Extech TP873 -
Extech Instruments Corporation
The Extech TP873 is a Bead Wire Type K Temperature Probe that can measure temperature from -30°C to 300°C (-22°F to 572°F). It is compatible with most test instruments that have a Type K Temperature input. Complete with a Type K mini connector and banana plug adaptor.