Showing results: 46 - 60 of 221 items found.
-
DS-0227A -
Ono Sokki
The trouble of rotation machinery is caused most frequently by unbalanced phenomenon of rotating shaft. However, balancing correction on-site is not easy because the conventional vector calculation method with drawing needs quite some time.
-
Bestone Industrial Ltd.
Used for measuring periodic motion, to check the imbalance and deflecting of moving machinery. Specifically designed for present measuring various mechanical vibration. So as to provide the data for the quality control, run time and equipment upkeep.
-
Bestone Industrial Ltd.
Used for measuring periodic motion, to check the imbalance and deflecting of moving machinery. Specifically designed for present measuring various mechanical vibration. So as to provide the data for the quality control, run time and equipment upkeep.
-
AFI-ESC1220 -
Astro Flight Inc.
The AFI-ESC1220 is an Electronic Speed Controller designed to drive BLDC motors. It meets the industrial requirements of high power and high voltage application for electronic vehicles, airplanes, boats and medium duty industrial machinery. It is rated at 24KW.
-
vocalZoom
Our non-contact vibration sensors help industrial manufacturers easily deploy highly accurate sensors on both new and old machinery - even for equipment that is wet, hot, moving, or too small to deploy traditional sensors on.
-
Ametek Spectro Scientific
We provide lab instruments, on-site oil analysis systems, and portable tools for a variety of customer needs . Our analyzers provide critical data about machinery condition and can provide an early warning of equipment failure.
-
Scien Co., Ltd.
A system for diagnosing failures of rotating machinery such as turbines, motors, pumps, fans, and compressors, which are major facilities in nuclear power, hydropower, thermal power plants, petrochemical plants, shipbuilding, and aviation, through displacement sensors.
-
PROTOR-mobile -
Prosig Ltd
PROTOR-Mobile is the ideal, investigative tool for mobile condition monitoring of rotating machinery. It provides the same extensive facilities as a standard PROTOR system but as a portable unit, rugged enough to withstand typical Power Station environmental challenges.
-
IMR 1440FL -
IMR Environmental Equipment, Inc.
The exhaust gas analyzer, IMR 1440FL/COFL, is designed to measure exhaust gases of Forklift Trucks, Generators, and heavy Machinery that are powered by a variety of fuels. According to US regulations, the IMR 1440FL/COFL can measure soot and CO for Forklift Trucks.
-
Integrated Test + Measurement
When taking vibration measurements on rotating machinery, it is crucial that you record tachometer pulses along with vibration data. A photoelectric sensor along with reflective tape that is attached to the rotating element will provide these speed pulses for data analysis.
-
PC15250 -
Martindale Electric Co. Ltd
Quickly and simply prove continuity of all 3 lines. Identifies which are faulty and shows the sequence of phase rotation. Fast & effective method of identifying worn or unmarked cables, and ensuring 3-phase outlets and machinery are wired correctly.
-
AFI-ESC610 -
Astro Flight Inc.
AFI-ESC610 is an Electronic Speed Controller designed to drive BLDC motors. It meets the industrial requirements of high voltage and high power motor application for electrical vehicles, airplanes, boats and medium duty industrial machinery. It is rated at 6KW.
-
Southwire Tools
This device truly stands out because of its fast response, high/low alarms and dual laser pointer. It is used by maintenance professionals to quickly locate worn machinery, hot spots in electrical panels and defective HVAC equipment.
-
Sper Scientific
The level of vibration is a useful guide to the balance, alignment and general condition of pumps, motors, and other machinery. Poor balance, misalignment, and looseness results in higher levels of vibration and indicates maintenance is required for operational as well as safety reasons.
-
MRC ltd.
Materials testing, measurement of the characteristics and behavior of such substances as metals, ceramics, or plastics under various conditions. The data thus obtained can be used in specifying the suitability of materials for various applications, building or aircraft construction, machinery, packaging etc.