Showing results: 31 - 39 of 39 items found.
-
PT-LabCar -
ETAS GmbH
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
BMS HIL -
Bloomy Controls, Inc.
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
DX-201 -
Dexing Magnet Tech. Co., Ltd
DX-201 digital fluxmeter is a precise magnetic measuring instrument, adopted low drift electronic integrator design and production. The most important features are test response quick, without data lose in the testing process. In the process of test samples flux by the Czochralski method, fast pull and slow pull datas are consistent, fine features especially shows in repeated measurements and regression testing. It can measure magnetic flux or magnetic moment matched with different fixtures according to users’ requirements.
-
TestNG -
TestNG
TestNG is a testing framework using annotations to provide a more powerful way to test your code in various ways: unit, regression, functional, integration, etc… TestNG allows you to clearly separate your Java code from the way your tests are run. You never need to recompile any of your classes if you decide to run a different set of tests or suites.
-
RF-LiveSim -
TestTree
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
TestingXperts
Test automation helps in reducing regression testing time and cutting down the time to market with significant cost savings on long term basis. However, a clear automation strategy and roadmap is key to ensuring the right return on investment on your automation initiatives. With disparate application architecture, multiple environments, third party integrations and multiple user devices, a standardized and consistent automation approach is needed to ensure high reusability, ease of maintenance and lower upfront cost.
-
Tessy -
Razorcat Development GmbH
TESSY automates the whole unit test cycle including regression testing for your embedded software in C/C++ on different target systems. As an easy-to-install and easy to operate testing tool TESSY guides you through the unit test workflow from the project setup through the test design and execution to the result analysis and reporting. TESSY takes additionally care of the complete test organization as well as the test management, including requirements, coverage measurement, and traceability.
-
Objective Interface Systems
Objective Interface Systems (OIS) was founded in 1989 with the goal of providing products that enable customers to build vastly superior information systems and technologies.OIS's products allow the system and software engineers to assemble flexible systems with incredibly agile communications infrastructures.The products enable real-time, embedded, and high-performance systems based on standards-based communications infrastructures on a wide variety of deployment environments. These tools result in systems that are more flexible, reliable, predictable, and correct than what was previously possible. OIS products are the Heart of Communications.OIS provides the most reliable products available. Every OIS software engineer is trained in DO-178B safety-critical engineering processes, Software Considerations in Airborne Systems and Equipment Certification. This well-established process standard arguably provides the best method for achieving high-correctness in engineering processes. Every line of OIS product source code goes through an arduous multi-person peer review and requirements traceability analysis. Critical sections get even more scrutiny. Every product build goes through automated regression testing and verification by a group independent of the developers.
-
Soft Hearts LLC
1. Distortion free stimulus even the equalized stimulus.2. Unlimited channels acquisition and processing. (Hardware limited)3. Human correlated listening test(Bark Scale intensity chart). (Requires large memory)4. Hi Res intensity chart for buzz/pop detection. (Requires large memory)5. Auto equalization method with target dBSPL accuracy.6. TCP client for test framework integration.7. Easy limits and logs development.8. Easy logs visualization module.9. Auto waveform alignment and triggering.(Upto single point alignment accuracy)10. Easy regression testing via TCP client.11. Standard Magnitude, Phase, THD, THD+N, Rubb&Buzz, Pink Noise, Noise Tests.12. Unlimited calibrations and equalization for scaling to different products and stations.13. Lowest test system and test sequence development times.14. Requires minimal training and debugging.15. Automatically avoid Reference speaker play and stop pops.16. WMD/ASIO driver compatible sound cards supported.(B&K 3670 recommended)
