Showing results: 16 - 30 of 412 items found.
-
AA-Ultrasonic -
IPEC Ltd.
The AA-Ultrasonic acoustic probe is designed for use on air insulated terminations where a clear sound path between the electrically stressed insulation and the probe is present. The sensor is extremely sensitive and can detect activity below 10pC. The probe has a magnetic base to allow coupling to steel enclosures and a swivel head as so the detecting sensor can be aimed directly at the HV point. Corona in air and surface tracking can seriously damage high voltage insulating surfaces in a way that will ultimately lead to flashover and complete failure of the insulator. This discharge activity creates acoustic emission that can be detected using a high frequency sensor. The magnitude of the acoustic emission is indicative of the degree and severity of the discharge activity.
-
AMI D9650 -
Nordson Corporation
Specifically designed to serve as a general purpose tool for failure analysis, process development, material characterization and low volume production inspection, the capabilities of the D9650 are truly unmatched. Representing the latest in C-SAM acoustic micro imaging, the D9650 delivers the unrivaled accuracy and robustness that you would expect from Nordson Test & Inspection instruments, plus improved electronics and software that raises the performance level for laboratory acoustic microscopes.
-
Reach Technologies Inc.
Reach Technologies' Acoustic Recorders provide cost-effective signal recording, analysis and playback. These units are highly configurable and come in a wide variety of chassis configurations, bandwidths and channel counts.
-
Linear Acoustics
Audio over IP (AoIP) has been embraced by the radio side of broadcasting for many years where the myriad advantages of networked audio via the Livewire+ AES67 standard is well known. Now, AoIP is available for television audio thanks to Linear Acoustic AERO.soft™. The Linear Acoustic SDI xNode de-embeds two separate HD/SD-SDI inputs, converts it to up to 16 channels of Livewire+ AES67 audio, makes it available for processing, upmixing, and encoding in the brand-new AERO.soft Processing Engine, and then re-embeds the audio into two independent SDI outputs. This provides unmatched flexibility, scalability and channel density.
-
PCB Piezotronics, Inc.
Measurements to evaluate and improve Building Acoustics are typically made to analyze and design noise control from room to room, or from outside to inside. Noise sources such as music systems, televisions, appliances, traffic, aircraft, and manufacturing are all around us. The field of Building Acoustics evaluates and designs the materials and methods to insulate and isolate us all from these sound sources when we are at work, rest, or enjoying leisure time. The resulting data is useful for evaluating compliance with building codes and for proposing countermeasures for areas of concern. These measurements often involve creating and measuring an artificial sound source, and then measuring the resulting noise in receiver locations.
-
Castle Group Ltd.
When you're ready to take noise measurements, it's strongly recommended that you perform a field calibration using an Acoustic Calibrator. You should calibrate your sound meter before you start to measure, and then once you've finished you should perform a reference check against the calibrator and make note of any drift that has occured. You can find out more about performing Field Calibrators by reading this post and watching a short video.
-
M+P International
Noise is increasingly the subject of new regulations for the protection of human health and safety as well as for improving the environment in general. As well as sound levels, the perceived sound quality of products from washing machines to vehicles is often an important part of the customer buying decision so must be considered during product development. m+p Analyzer for noise and vibration measurement and analysis provides a full range of capability for these applications. Real-time fractional octave filters satisfy all acoustic applications from simple sound pressure, sound power for equipment legislative requirements, intensity mapping to isolate sources to sound quality metrics for product refinement.
-
CAL150 -
Larson Davis, Inc.
The Larson Davis CAL150 Sound Level Calibrator is a battery operated precision microphone calibrator used for the calibration of sound level meters and other sound measurement equipment
-
CAL250 -
Larson Davis, Inc.
The Larson Davis Model CAL250 is a battery operated precision microphone calibrator used for the calibration of sound level meters and other sound measurement equipment.
-
CAL200 -
Larson Davis, Inc.
The Larson Davis CAL200 Sound Level Calibrator is a battery operated precision microphone calibrator used for the calibration of sound level meters and other sound measurement equipment.
-
RESON TC 3021 -
Teledyne Marine RESON B.V.
The TC 3021 is our entry-level, universal 2MHz transducer and is ideal for high precision sound velocity measurements over short distances.
-
RESON TC 1037 -
Teledyne Marine RESON B.V.
Originally designed for underwater telephone systems, the TC 1037 is a rugged directional transducer ideal for operating at low frequencies.
-
RESON TC 2178 -
Teledyne Marine RESON B.V.
The TC 2178 is a hydrodynamic dual-frequency transducer, ideal for navigation and carrying out hydrographic surveys. The hydronamic shape in combination with integrated mounting bracket and rope connection points allows for easy over-the-side use on smaller vessels.
-
Studio Six Digital
Includes cursor readout of dB bands, max & min lines, noise curve overlays, pink noise generator, and optional STC Transmission Loss.
-
AMI D9650Z -
Nordson Corporation
The D9650Z incorporates the latest C-SAM technology with enhanced features to accommodate the testing of Power Modules as well as performing standard C-SAM operations. This new system configuration is optimized for inspection of heatsink bond integrity, thickness of bond layer and wire bond welds. Powered by our Sonolytics software platform with PolyGate technology, the D9650Z is ideal for failure analysis, process development and QC screening in low-volume production environments.