Showing results: 46 - 55 of 55 items found.
-
8024 -
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. 3-Hole solder pads both sides. Pad and bus surfaces solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
8020 -
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad-Per-Hole and peripheral bus both sides. Pad and bus surfaces not solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
Comtel Electronics
ANSI/VITAV 1-1994 VME32 Backplane, 6U 5 Slot Including J1 & J2.Benefits:• Standard VME backplanes are available also in other slot count configurations• Surface Mount Technology – Excellent high frequency performance, high reliability and reduced cost due to SMT
-
YAVAL964 -
6TL Engineering
- 16 channels DPDT or SPDT 2A- CAN bus control and 24Vdc (J1 and J2 connectors to chain multiple cards).- Access to relay-pins through wire-wrap or terminal block- Address selection DIP switch on top layer- LED monitoring- Drivers dll & VIs available
-
8028 -
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad per hole both sides. Combination Pattern: 0.100", 0.050" and 2mm grid.Pad and bus surfaces solder coated.Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
8018 -
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector.Pad-Per-Hole both sides.Combination Pattern: Half 2mm grid and other half 0.1” grid. Pad and bus surfaces solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
MS 2015 -
Meltronics Systemtech
Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.
-
SEN-30103-J1 -
Playing With Fusion Inc
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
MS 1508 -
Meltronics Systemtech
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
MS 1501 -
Meltronics Systemtech
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS