Showing results: 61 - 73 of 73 items found.
-
midUTS -
Bloomy Controls, Inc.
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Quantifi Photonics Inc.
Coherent Solutions’ expanding portfolio of PXIe optical test modules bring a wide range of new mixed-signal test capabilities to the PXI platform. The new modules offer seamless integration with PXI Platform and deliver reliable and repeatable results across a wide range of optical and mixed-signal test applications.
-
E9902G -
Keysight Technologies
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
S-112 -
Notice
Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.
-
-
XGT-200 -
ShinewayTech
The Ethernet test engine XGT 200 provide a comprehensive test for next generation Ethernet solution. There are many different test modules, it can help clients to verify the performance of their Ethernet. XGT-200 have two 10/100/1000Mb/s RJ45 , two 100/1000M SFP and two 10Gbps SFP+ it can generate test profession streams that you need and analyze them ,then provide the test result. XGT-200 provide install and maintain services and activate new profession service. XGT-200 can provide many kinds of test functions, it can help you to control and know the quality of your Ethernet.
-
Eye-BERT MicroX -
Spectronix
The Eye-BERT MicroX is a compact, easy to use test solution offering high performance bit error rate testing at a fraction of the cost of competing solutions. The unit is offered in two speed grades including the X10 which operates up to 14.5Gbps, and the X30 which extends the data rate to 29Gbps. Its broad data rate capabilities and long test patterns make this unit suitable for testing nearly all optical SFP, SFP+, and SFP28 transceivers in production with just one unit. The real-time eye opening monitor and eye scanning capability can aid in troubleshooting by providing the operator with additional link quality information. Other features include Autonomous pattern detection, SFP diagnostic tools, and wavelength tuning (per transceiver capability). With a click of a button the Eye-BERT MicroX will automatically test an SFP module based on its advertised capabilities and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
EV-SFP-171 -
UC Instruments, Corp.
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
iOptics -
EXFO Inc.
iOptics offers a complete, powerful and easy-to-use tool for CFP and QSFP qualification and can validate the full range of low- to high-rate transceivers including SFP, SFP+, XFP, CFP, CFP2, CFP4, QSFP+ and QSFP28. iOptics offers a faster, streamlined and automated test sequence aimed at quickly and simply validating any type of 10M to 100G interface. It is the ideal solution for multirate field commissioning with a simple one-button pass/fail. It offers automated stress testing for lab qualification and is also ideally suited for data center and data center interconnect (DCI) testing.
-
ARINC 664 -
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
PXIe-FC4 -
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
AIM GmbH
AIM’s Fibre Channel test, simulation and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive and scalable DDR3 memory and IRIG-B time encoder/decoder functions are standard. The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The dual core processor provides onboard processing and data transfer capabilities for the most demanding Fibre Channel applications including upper layer protocol support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized Fibre Channel interfaces enabling the board to analyze incoming and modify outgoing data in real time. Each module provides 2 Fibre Channel compliant full duplex ports, implementing the full link level services. SFP cages make it suitable for different media types as optical or electrical network technologies. Ports operate either in Traffic Simulator or Analyzer/Monitor mode with support for port related Frame Statistics. Sophisticated packet capturing mechanism and monitoring features are complimented with powerful triggering and filtering capabilities.
-
AIM GmbH
> ARINC818 is a specification which has become an Industry standard for the transmission of uncompressed digital video. This commercial standard uses Fibre Channel as a point-to-point communication link for low latency with the ARINC818 defining the packetized protocol for transmission of the digital video information. It is highly flexible and can be used for a variety of onboard display systems in both commercial and military applications. AIM’s ARINC818 cards use our field proven Common Core hardware design giving the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive DDR3 memory and IRIG-B time encoder/decoder functions are standard. The ARINC818 modules are available in PCIe formats.The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for ARINC818 interfaces. The dual core processor provides onboard processing and data transfer capabilities for the most demanding applications including ARINC818 support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized ARINC818 Interfaces enabling the board to analyze incoming data in real time. Each module provides 2 ARINC818 compliant ports. SFP cages make it suitable for different media types as optical or electrical network technologies. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our ARINC818 cards.
