Showing results: 241 - 255 of 1524 items found.
-
MS 1601 -
Meltronics Systemtech
The WEAPON CONTROL SYSTEM SIMULATOR (WCSS) is used to simulate Aircraft Bomb and Rocket release commands for the LAB testing of WCSTS. The WCSS system simulates the High current and Low current signals according to the mode of operation (Series).
-
GEPS-2000 -
GF Instruments, s.r.o.
Geoelectric Power Sounder GEPS-2000 is a device for data acquisition and interpretation of deep VES (vertical electrical sounding) as well as for 8 channel profiling (resistivity and IP sections). It can be used for measurements up to 1000 – 2000 m depth allowing both high voltage and high current injection of transmitter current according to real measuring conditions.
-
40-183B-011-HI -
Pickering Interfaces Ltd.
The 40-183B-011-HI has 6 high current SPST switches with hardware interlock in two PXI chassis slots. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
SC6540 -
Associated Research
Our patented SC6540 modular scanning matrix pioneered the largest productivity improvement in the electrical safety compliance industry in years. With up to 16 independent high voltage or high current channels in a convenient 2U design, the SC6540 can be customized in 10 different configurations for multi-point Hipot, Ground Bond, Insulation Resistance and Leakage Current testing.
-
1625A -
Ballentine Laboratories, Inc.
The BLI 1625A is a multiranging, high accuracy, active current shunt, for use in making NIST traceable measurements of currents from 10 microamperes to 100 Amperes. Very high measurement stability has been achieved in our shunt design by using special alloys, compensated by a proprietary Ballantine process to minimize temperature coefficient effects.
-
66203/66204 -
Chroma Systems Solutions, Inc.
Voltage Range :15/30/60/150/300/600 VrmsCurrent Range :0.005/0.02/0.05/0.2/0.5/2/5/20 ArmsFrequency Range : DC, 15Hz~10kHzEmbedded high speed DSP, 16 bits Analog/Digital convertersHalf rack size, 4 input modules design (66204)Support different wiring configuration power measurement (1P2W/1P3W/3P3W/3P4W)Support external shunt and CT for higher current measurement application5 mA minimum current range & 0.1mW power resolutionMeets ENERGY STAR / IEC 62301 /ErP measurement requirementsAccumulated energy methods for unstable power measurementUser-define criteria provides automatic PASS/FAIL indicationsDual current shunt design provides high accuracy over a wide current rangeTHD and user-specify order distortion measurementInrush current and energy measurementVoltage/ Current harmonics measurement up to 50 orders
-
7610B -
Peaceful Thriving Enterprise Co Ltd
This is a stable, low power consumption, and high accuracy 3 1/2 digits (2000 counts) leaking current tester for automobile. Leaking current for automobile is generally as small as milliamps, which is hard to measure by clamp meter. By plug this meter with the fuse box, user is able to measure leaking current as small as 1 mA.
-
DAM2 -
Lifasa - International Capacitors, SA
DAM switching capacitors are used to protect semiconductors (IGBT transistors). These are charged and discharged repeatedly with high current peaks.
-
DAM3 -
Lifasa - International Capacitors, SA
DAM switching capacitors are used to protect semiconductors (IGBT transistors). These are charged and discharged repeatedly with high current peaks.
-
ZAHNER-Elektrik
Ready to use extension packages for special methods e.q. high current interrupt or AC-DC-AC test on laminates.
-
Sens-X -
Add2 Ltd.
Sens-X intelligent sensors offer a range of high dynamic range sensor hardware for the capture of specialist current measurements.
-
40-667A-012 -
Pickering Interfaces Ltd.
The 40-667A-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
40-666B-012 -
Pickering Interfaces Ltd.
The 40-666B-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
40-667C-011 -
Pickering Interfaces Ltd.
The 40-667C-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
40-667A-011 -
Pickering Interfaces Ltd.
The 40-667A-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.