Showing results: 226 - 240 of 687 items found.
-
Fairview Microwave Inc.
Fairview Microwave’s electromechanical switches exhibit extremely low insertion loss repeatability with guaranteed levels of 0.03 to 0.05 dB over 5 to 10 million switching cycles, depending on the model. Performance includes low insertion loss of 0.3 dB with high isolation of 100 dB typical, and input power ratings of up to 70 watts CW and up to 1 watt for hot switching applications. These switches cover broadband frequencies from DC to 40 GHz and are offered in three configurations: single-pole double-throw (SPDT), single-pole four-throw (SP4T) and single-pole six-throw (SP6T).
-
PGY-RFFE-EX-PD -
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
Mors Smitt Group
A latching relay is a two-position electrically-actuated switch. It maintains either contact position indefinitely without power applied to the coil. It is controlled by two momentary-acting switches or sensors, one that 'sets' the relay, and the other 'resets' the relay. The latching relay maintains its position after the actuating switch has been released, so it performs a basic memory function.
-
GTPD-2C -
Kingrun Instrument Co., Ltd.
GTPD-2C Digital partial discharge tester is the digital partial discharge measuring and analyzer adopting the complete new generation technology. It is suitable for partial discharge detection in manufacturing factory and field handover test of transformers, generators, CT/PT, bushings, GIS, capacitors, power cables, switches and other high-voltage electrical equipment with various voltage levels and capacities.
-
RA 19 -
Kepco, Inc.
The 1U high rack adapter will mount four of the low profile 50W, 100W and 150W (Series HSF-1UR or HSF-1U) power supplies. Each plug-in power supply is equipped with a power on/off, indicator LEDs and voltage test points. The RA 19-1U provides access to the DIP switches and rack keying without disassembling the rack. It also provides a redundant scheme with modules 1 and 3 being powered from one a-c input and modules 2 and 4 from a second a-c input. Module numbering is left to right facing the front panel.
-
N7745C -
Keysight Technologies
Keysight's popular N7745A optical power meters with eight power-sensor channels provide increased throughput and operational efficiency to meet today's challenges in manufacturing. Designed for characterizing optical multiport components, these optical power meters offer industry-leading solutions for device connectivity, high-speed measurement data acquisition and fast data transfer for post-processing. The multiport power meter enables fast measurement solutions for all multiport devices; for example multiplexers, PON splitters, wavelength selective switches (WSS) and ROADMs, as well as compact setups for simultaneous testing of multiple single-port devices.
-
116EXT6122-012XR -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
116EXT6122-0125R -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
110EXT9122-0000 -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
110EXT6122-000X -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
111EXT9140-0120 -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
111EXT6122-012X -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
111EXT6140-012X -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
110EXT3140-10xx -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
110EXT3122-10xx -
ELMA Electronic, Inc.
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.