Showing results: 391 - 405 of 684 items found.
-
PRV-1059 -
Curtiss-Wright Defense Solutions
The Parvus PRV-1059 is a rugged VLAN-capable 5-port PC/104 Fast Ethernet switch featuring very low power consumption and highly reliable extended-temperature operation up to +85°C (185°F). Supporting auto-MDI-MDIX network installation, the board is designed for simple plug-and-play operation, enabling up to five embedded computing devices to be networked together using 10BaseT or 100BaseTX Local Area Network (LAN) connections.
-
Model 8064 OEM -
ICS Electronics
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
95004 -
HITEC Sensor Solutions Inc.
The Fail-Safe rotary speed control is a fluid/magnet actuated mechanical switch. It incorporates the consistent and dependable forces of gravitation and magnetism to achieve its mechanical switching action. Because the unit requires no electrical power to operate, it can be used in remote areas where access to power supply is inconvenient or unavailable.
-
OP-FW10 -
LINEEYE Co., Ltd.
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
-
FMC645 -
Sundance Multiprocessor Technology Ltd.
The FMC645 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6455 device. The FMC645 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), has a high-pin count connector and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces.
-
Chroma ATE Inc.
Support 8K SHV (Super Hi-Vision 7680x4320 / 8192x4320)Support full 8K scrolling functionIndependent signal and power module designDual-core graphics processing architecture - Increase graphics and data transmission performance - 8K Super Hi-Vision images switch in less than 200msSupport 6/8/10/12 bits color depth (12 bit only in LUT mode)Support user edited test patterns - BMP pattern format - Maxi. 300 of 8Kx4K bmp patternsSupport VDIM and PWM dimming functionSupport cross coordinates defect positioning functionSupport auto flicker adjustment (with A712306)Support gigabit Ethernet control interfaceSupport USB port for data update
-
FMC667 -
Sundance Multiprocessor Technology Ltd.
The FMC667 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6678 device. The FMC667 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces. Several Gigabit differential pairs from the FMC connector are used to implement a PCIe and Serial Rapid IO interface between the FMC and the carrier.
-
FC2000 Series -
ACECO Electronics Corp.
A professional frequency counterFrequency range: 1 Meg ohm and 50 ohm input for full range 10 Hz - 3 GHzWeight: 250 gCase: 100 mm * 68 mm * 31 mm stamped aluminum with black anodized finishBattery: Internal 4 * AA 600 mAH NiCd pack10 digit liquid Crystal DisplayLow power consumption (Average 6 hour battery life)Hold switch to lock displayLow battery indicatorUltra sensitive synchronous detector 16 section bargraph to show RF signal strengthHigh speed 300 MHz direct counter with 0.1 Hz resolution4 selectable gate speedsAutomatic holdMeasure frequency and periodBeeper and LED back light with black anodized finis
-
ICS Electronics
All of ICS's GPIB Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Model 4804B -
ICS Electronics
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Model 4864 OEM -
ICS Electronics
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
FC3000 Series -
ACECO Electronics Corp.
The latest advance in RF finder Frequency range: 10 MHz - 3 GHz Weight: 210g Case: 80 mm * 68 mm * 31 mm stamped aluminum with black anodized finish Battery: Internal 4 * AA 600 mAH NiCd pack 7 digit liquid Crystal Display with 1 KHz resolution Low power consumption (Average 6 hour battery life) Hold switch to lock display Digital filter prevents display of random noise Low battery indicator Ultra sensitive synchronous detector 16 section bargraph to show RF signal strength Automatically holds and tunes ICOM CI-V or AOR receivers Measure frequency and period
-
SM-8X8-C6HDR-POE-HDBT -
Network Technologies Inc
The VEEMUX® HDMI Matrix Switch Over HDBase-T with Power Over Ethernet routes and distributes uncompressed HD 1080p, multi-channel audio, Ethernet, and IR from eight HDMI video sources to eight displays via inexpensive CAT6a/7 cable using HDBase-T technology. Power over Ethernet provides power to receivers that can be located up to 328 feet away.
-
SKS-H04GA -
Shanghai Sanki Electronic Industries Co., Ltd.
The high-frequency noise simulation generator is an EMC test instrument that reproduces high-frequency noise with a fast rise time when the switch is turned on/off. Since the pulse rise time is less than 1ns and contains wide bandwidth noise, it is very suitable for reproducing malfunctions. The line noise entering the power line and the induced noise entering the communication line can be reproduced, and the performance evaluation of the malfunction and function degradation of electronic products can be performed.
-
Series BOP-HV -
Kepco, Inc.
The Kepco Model BOP 500DM and BOP 1000DM are high voltage power sources, up to 500V or 1000V, respectively. These combine the capabilities of fast programmable power supplies with a Class A output stage, which can respond bidirectionally from zero. The BOP-HV can be operated in either a "voltage stabilizing" or "current stabilizing" operating mode (selectable by a front panel switch). These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
