Showing results: 646 - 660 of 684 items found.
-
273 HP -
Standard Electric Works Co., Ltd
● 2 ranges for selection : LOW 50V~1.5kV HIGH 1.5kV~132kV● There is no power consumption in off mode : 0uA● Nice mechanical slide switch for function selection : HIGH / OFF / LOW ● The power consumption in low voltage detection mode : Less than 20mA● The power consumption in high voltage detection mode : Less than 20mA● Bright LED and audible alarm sound when voltage is present.● Lightweight, robust and compact.● Efficient and easy to use● Users have to use the Hot Stick when test high voltages between 1.5kV~132kV.● SEW provides nice optional accessories of Hot Sticks HS-175 and HS-120 for high voltage detection.● Optional accessories : HS-175 Telescopic hot stick (triangle-type) HS-120 Hot stick
-
2960 CL -
Standard Electric Works Co., Ltd
● True RMS measurement.● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).● Re-power on by pushing any of the push buttons or by changing the rotary switch mode after auto power off.
-
855 PRA -
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
855 PR -
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Lamps let you determine at-a-glance if phase is open.● Large size alligator clips for easy clipping onto switch-boards terminals.● Checks a wide range of 3-phase power sources.● Special test leads length are available on request.● Push button switch is designed to minimize damage due to negligence.
-
863 PR -
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Neon light indicators.● Large size alligator clips for easy clipping onto switch- boards terminals.● Allows you to check a wide range of 3-phase power sources.● Special test leads length are available on request.
-
39E12WUX98Y2VCM0-SOSA1 -
ELMA Electronic, Inc.
3U OpenVPX development platform aligned with SOSA 1.0. It supports both SOSA and CMOSS profiles. It includes: 2 I/O intensive SBC, 7 primary payload, 1 radial clock, 2 switch and 2 power. Includes VITA 67.3 RF and optical I/O modules.
-
EM-6947 | 200 MHz – 5 GHz -
Electro-Metrics Corp.
The EM-6947 is an ultra-wide bandwidth log periodic dipole array aimed at applications requiring consistent performance over a very wide frequency range. Capable of both receiving and moderate power level transmitting, the EM-6947 can take the place of two or more conventional antennas, allowing you to take full advantage of the tuning range capabilities of modern receiver and spectrum analyzer designs with less inconvenience caused by the need to switch antennas.
-
TS2X020 -
Intelligent Charging
The TS2X020 is a portable lightweight battery charger intended for rapid charging of vehicle batteries in the field without the attendant weight penalties usually associated with the operation. The charger is a constant voltage unit, and the charging current is regulated by the battery terminal voltage, with current limit of 20 Amps on 24v output, and 40 Amps on 12v output. Switch mode technology provides high efficiency; both in power to weight ratio, and input to output ratio.
-
1260-120 -
Astronics Corporation
Each channel of the 1260-120 can switch up to 13A, 250VAC or 10A, 125VDC; its switching capability makes it the ideal solution for applications requiring high-current switching of AC power, DC power supplies, and AC or DC current sources.
-
778858-01 -
NI
96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module—The PXI‑6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
75D4-H2 -
North Atlantic Industries
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
EOS-JNX Series -
ADLINK Technology Inc.
The EOS-JNX series has a built-in Smart PoE feature to control PoE power remotely to reduce maintenance efforts in challenging environments and provides PoE power loss detection to alert of any unexpected PoE disconnection. The EOS-JNX-I is designed as an AI PoE switch for connecting to IP cameras to enable AI inferencing, and also provides an uplink port to connect to a network video recorder (NVR) for recording video streams, making upgrading existing surveillance systems easy. The EOS-JNX-G is designed for industrial AI machine vision applications, providing a dedicated bandwidth of 1Gb per channel with a GigE camera connection, which is crucial for production line and manufacturing applications.
-
Meltronics Systemtech
- Auto Learning for slow detection and easy commissioning.- Encoder signal for floor detection.- Detail diagnostic of individual components ensures safety and reliable operation- Attached ARD for each panel for rescue in case of power fail.- Intelligent algorithm to attend any calls within 10 seconds for standard configuration.- VIP option, Fireman switch, overload protection $ protection of all other standard interfaces integrated.- Announciator is integrated with Gong bell.- Preferable selection of floor by user, software functional options, Delay times and important configurations.- Error diagnosis by PC interfaces, eleavator error history and services details make your maintenance job very effective and efficient in time period
-
Carl E. Holmes Company
- 12 Pulse SCR Controlled Power Supply, P/N 19435PS- Input: 480 VAC, 300 Amps, 3 PH, 60 Hz- Output: 0 to 3000 VDC ± 10%, 80 Amps max adjustable with potentiometers, and 4/20 mA input signals from the PLC- Output voltage and current are provided as 4/20 mA signals to PLC- Contactor and overload relay are installed for protection- Power ON Light- Start / Stop capability- EPO capability- Manual voltage control and current limit- PLC interface- Output voltage and current are displayed on the voltmeter and ammeter.- A selector switch is used to select between manual Control or PLC Control- The customer is responsible for the PLC controller and PLC programming- Power enclosure, 68″H x 65″W x 44″D- Control enclosure: 20″H x 16″W x 9″D- Weight: 5000 lbs. approximately- All input/output connections are inside the enclosure
-
SG61000-5 -
Lisun Electronics Inc.
Automatic lightning surge generator (or Lightning surge immunity) SG61000-5 is used to assess the power cord and connect the internal switch stood in line to connect the internal switch to provide a common basis for switching the natural world and lightning caused by the high-energy transient interference performance. Performance fully meets the IEC 61000-4-5, EN61000-4-5 and GB/T17626.5 standards.
