Filter Results By:
Products
Applications
Manufacturers
-
product
Ethernet to Relay Interface Boards
Model 8064 OEM
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
product
Fail Safe Mechanical Speed Sensor
95004
The Fail-Safe rotary speed control is a fluid/magnet actuated mechanical switch. It incorporates the consistent and dependable forces of gravitation and magnetism to achieve its mechanical switching action. Because the unit requires no electrical power to operate, it can be used in remote areas where access to power supply is inconvenient or unavailable.
-
product
Firmware for High-speed HDLC Mode
OP-FW10
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
-
product
Fixed-Point C6455 DSP Module
FMC645
Sundance Multiprocessor Technology Ltd.
The FMC645 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6455 device. The FMC645 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), has a high-pin count connector and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces.
-
product
Flat Panel Display Test Solutions
Support 8K SHV (Super Hi-Vision 7680x4320 / 8192x4320)Support full 8K scrolling functionIndependent signal and power module designDual-core graphics processing architecture - Increase graphics and data transmission performance - 8K Super Hi-Vision images switch in less than 200msSupport 6/8/10/12 bits color depth (12 bit only in LUT mode)Support user edited test patterns - BMP pattern format - Maxi. 300 of 8Kx4K bmp patternsSupport VDIM and PWM dimming functionSupport cross coordinates defect positioning functionSupport auto flicker adjustment (with A712306)Support gigabit Ethernet control interfaceSupport USB port for data update
-
product
Floating-Point C6678 DSP Module
FMC667
Sundance Multiprocessor Technology Ltd.
The FMC667 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6678 device. The FMC667 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces. Several Gigabit differential pairs from the FMC connector are used to implement a PCIe and Serial Rapid IO interface between the FMC and the carrier.
-
product
Frequency Counter
FC2000 Series
A professional frequency counterFrequency range: 1 Meg ohm and 50 ohm input for full range 10 Hz - 3 GHzWeight: 250 gCase: 100 mm * 68 mm * 31 mm stamped aluminum with black anodized finishBattery: Internal 4 * AA 600 mAH NiCd pack10 digit liquid Crystal DisplayLow power consumption (Average 6 hour battery life)Hold switch to lock displayLow battery indicatorUltra sensitive synchronous detector 16 section bargraph to show RF signal strengthHigh speed 300 MHz direct counter with 0.1 Hz resolution4 selectable gate speedsAutomatic holdMeasure frequency and periodBeeper and LED back light with black anodized finis
-
product
GPIB Digital Interfaces
All of ICS's GPIB Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
product
GPIB Serial Interface
Model 4804B
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
product
GPIB to Relay Interface Boards
Model 4864 OEM
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
product
Handheld RF Finders
FC3000 Series
The latest advance in RF finder Frequency range: 10 MHz - 3 GHz Weight: 210g Case: 80 mm * 68 mm * 31 mm stamped aluminum with black anodized finish Battery: Internal 4 * AA 600 mAH NiCd pack 7 digit liquid Crystal Display with 1 KHz resolution Low power consumption (Average 6 hour battery life) Hold switch to lock display Digital filter prevents display of random noise Low battery indicator Ultra sensitive synchronous detector 16 section bargraph to show RF signal strength Automatically holds and tunes ICOM CI-V or AOR receivers Measure frequency and period
-
product
HDMI Matrix Switch Over HDBase-T with Power Over Ethernet (PoE)
SM-8X8-C6HDR-POE-HDBT
The VEEMUX® HDMI Matrix Switch Over HDBase-T with Power Over Ethernet routes and distributes uncompressed HD 1080p, multi-channel audio, Ethernet, and IR from eight HDMI video sources to eight displays via inexpensive CAT6a/7 cable using HDBase-T technology. Power over Ethernet provides power to receivers that can be located up to 328 feet away.
-
product
High Frequency Noise Simulator
SKS-H04GA
Shanghai Sanki Electronic Industries Co., Ltd.
The high-frequency noise simulation generator is an EMC test instrument that reproduces high-frequency noise with a fast rise time when the switch is turned on/off. Since the pulse rise time is less than 1ns and contains wide bandwidth noise, it is very suitable for reproducing malfunctions. The line noise entering the power line and the induced noise entering the communication line can be reproduced, and the performance evaluation of the malfunction and function degradation of electronic products can be performed.
-
product
High Voltage Linear Power Supplies Bipolar 4-quadrant, Analog/Digital/Local Control, Ultra Low Ripple/Noise
Series BOP-HV
The Kepco Model BOP 500DM and BOP 1000DM are high voltage power sources, up to 500V or 1000V, respectively. These combine the capabilities of fast programmable power supplies with a Class A output stage, which can respond bidirectionally from zero. The BOP-HV can be operated in either a "voltage stabilizing" or "current stabilizing" operating mode (selectable by a front panel switch). These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
product
ITA Terminal Blocks
YAVTB000
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
product
LilyPad Simple Power
The LilyPad Simple Power is a simple e-textile board with a 500mA charge rate that lets you connect and charge a lipo battery and switch it on or off, that's it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no trouble in added a bit of power to your next wearable circuit.
-
product
Linear Bench Power Supplies Local Control, Ultra Low Ripple/Noise
Series MSK
Kepco's MSK linear power supplies provide a selection of five models, offering 100 Watts of stable benchtop power. They use a high gain linear (series pass) stabilizer circuit for ultra low noise and low ripple output, good stability, and accurate resettability, and they are MIL-STD-461 compliant.MSK's "Preview" switch (d-c on-off) allows voltage and current to be pre-set with the digital meters displaying the set values. At "d-c off," no voltage is applied to the output terminals and no load current needs to be drawn to set the current limit. At "d-c on," the set voltage is applied to the output terminals, the appropriate mode indicator illuminates and the meters indicate actual voltage and current.
-
product
LXI Remote AC Power Management Switch
60-200-001
If you have ever read the term “programmable except for the supply on/off switch” the 60-200 can provide this capability in a system with the added benefit of an easy to use LXI interface. The 60-200 is a power management switch that provides a means of remotely controlling the power status of up to 8 instruments.
-
product
MFJ Dummy Load/Wattmeter
MFJ-267
1.5 kW Dry Dummy Load has built-in precision, true peak-reading SWR/Wattmeter switchable to external antenna! Worlds most versatile 1.5 kW dummy load has a built-in true peak reading SWR/Wattmeter that you can switch and use independently! Youll find tons of uses! Tune up your transceiver, linear amplifier, or antenna tuner into a safe 50 Ohm dummy load at full power.
-
product
Modular Relay Board
Alliance Support Partners, Inc.
An increasing number of electronics products are being assembled in panels of 8 or more to minimize production cost. These products are typically tested with in-circuit tests (ICT) followed by power-on functional tests. Normally, ICT requires isolation of power and ground while measurements are being performed. Functional tests, including in-system programming (ISP), require board power to be applied. The Modular Relay Board (MRB) is designed to switch power onto each individual board and to disconnect sensitive signals during functional test.
-
product
Motorized Linear Actuators with Built-in Stepper Motors and Controllers
A-LAR Series
Zaber's A-LAR Series products are computer controlled, lead screw driven, motorized linear actuators (electric cylinders). They are stand-alone units requiring only a standard 48 V power supply. A manual knob at the end of the unit permits manual control - press and hold to switch between velocity mode and distance mode, turn to move the actuator, and press to stop.
-
product
MTCA.3 Conduction Cooled MicroTCA Carrier Hub (MCH)
UTC041
The VadaTech UTC041 is the most feature-rich conduction cooled MicroTCA Carrier Hub (MCH) on the market. Its management software is based on VadaTech’s robust Carrier Manager and Shelf Manager which have been deployed for years with proven results. The MCMC manages the Power Modules, Cooling Units, and up to 12 AMCs within the chassis. It also manages PCIe Gen3 or 10GbE XAUI fabric switch as well as the standard GbE with 10GbE uplink Base Channel switch.
-
product
Multi-Meter
TW3207
Techwin(China) Industry Co., Ltd
Multi-Meter TW3207 integrates the functions of an intelligent optical power meter module and of a highly stable light source module in one unit which can perform closed-loop tests by incorporating both modules. Individual regimes of operation can also be manually chosen using menu operation to switch functions. A perfect combination to make your optical fiber tests a lot more convenient.
-
product
OEM SOLUTIONS - Optical Switch Modules From 4x4 Up To 144x144 Ports
Polatis Optical Switch Modules (OSM) are high-performance, fully non-blocking all optical matrix switch modules with port counts from 4x4 up to 144x144. Versions are also available for "any-to-any" port connectivity, which enables new interconnection architectures not possible with traditional symmetric NxN switch matrixes. The modules are designed for easy integration by OEMs integrating all optical switching with network equipment and are designed to meet the highest performance and reliability needs of the most demanding applications with exceptionally low optical loss, compact size, low power requirements and fast switching speeds.
-
product
Optical Receiver
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Return path optional. Frequency splitting according to customer’s need.* 2 RF outputs, level ≥104dBμV when optical input @ -1dBm.* Output level tunable through buttons on front panel.* RF Test Point on front panel.* High quality switch power supply.
-
product
Other Switching Power Supplies
PeakTech Prüf- und Messtechnik GmbH
The switching power supply technology used ensures high performance with a small size and low weight. 6 different DC output voltages (3 V / 4.5 V / 6 V / 7.5 V / 9 V and 12 V) can be set using a slider. With the 4 mm pole terminals, you can easily connect single wires but also 4 mm banana plugs. The power cord with an Euro plug is firmly connected to the power supply unit, whereby the device is switched off and on via a rear power switch. This handy power supply fits on every work bench and can be used universally in the hobby area, service or training.
-
product
Paddlewheel Flow Sensor
2537
The Signet 2537 Flow Sensor is the next generation in fluid measurement technology from the inventor of the original paddlewheel flowmeter. This sensor is an enhancement on what is already an industry standard. It has the added functionality of various output options including flow switch, pulse divider, digital (S3L) or 4 to 20 mA. Additionally, it offers low flow, low power and high resolution and can be configured on-site directly through the built-in user interface.
-
product
PCI Fault Insertion Switch Range for Differential Serial Interfaces
50-200/201
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.
-
product
Portable Load Bank
LBP-350
Designed to provide an adjustable load for troubleshooting or demonstrating welding power sources or generators. Includes analog meters for AC and DC output with jacks for external metering connections.13 ft 115V power cord. Seven 50 amp load switch.
-
product
POWERBOX H
The Innerspec POWERBOX H is the only hand-held, battery operated instrument capable of generating up to 1200V or 8kW of peak power at speeds of up to 300Hz. For pulse-echo operation, a built-in transmitter/receiver switch permits connecting directly to the instrument with no additional hardware.